- 您现在的位置：买卖IC网 > Datasheet目录611 > 90075-1 (TE Connectivity)ASSY SAHT Datasheet资料下载
参数资料
| 型号： | 90075-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | ASSY SAHT |
| 标准包装： | 3 |
| 系列： | Certi-Crimp |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 端子，20-26 AWG |
| 特点： | 侧面插入，棘齿 |
408-7092
4. Inspect the tool, with special emphasis on
checking for worn, cracked, or broken crimping
dies. If damage to any part of the head is evident,
return the tool for evaluation and repair (see Section
5, REPLACEMENT AND REPAIR).
B. Crimp Height Inspection
Crimp height inspection is performed through the
use of a micrometer with a modified anvil,
commonly referred to as a crimp height comparator. ?
TE does not market crimp height comparators.
Refer to Instruction Sheet 408-7424 for detailed
information on obtaining and using a crimp height
comparator.
Refer to Figure 4 and proceed as follows:
1. Refer to the chart in Figure 4 and select a
terminal and a wire (maximum size) for each crimp
section.
2. Refer to Section 3, CRIMPING PROCEDURE,
and crimp the terminal(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the chart,
the tool is considered dimensionally correct. If not,
return the tool for evaluation and repair (refer to
Section 5, REPLACEMENT AND REPAIR).
Position Point on
Center of Wire Barrel
Opposite Seam
Modified
Anvil
“A”
±0.05 [±.002]
2. Position the terminal and wire between the
crimping dies, as described in Section 3,
CRIMPING PROCEDURE.
3. Holding the wire in place, squeeze the tool
handles together until the CERTI-CRIMP ratchet
releases. Hold the handles in this position,
maintaining just enough tension to keep the dies
closed.
4. Check the clearance between the bottoming
surfaces of the crimping dies. If the clearance is
0.025 [.001] or less, the ratchet is satisfactory. If the
clearance exceeds 0.025 [.001], the ratchet is out of
adjustment and must be repaired.
If the tool conforms to these inspection procedures,
lubricate it with a thin coat of any good SAE 20 motor
oil and return it to service.
5. REPLACEMENT AND REPAIR
The parts listed in Figure 5 are customer- replaceable.
A complete inventory can be stocked and controlled to
prevent lost time when replacement of parts is
necessary. Order replacement parts through your ?
TE Connectivity representative, or call ?
1-800-526-5142, or send a facsimile of your ?
purchase order to 1-717-986-7605, or write to:
CUSTOMER SERVICE (038-035) ?
TYCO ELECTRONICS CORPORATION ?
PO BOX 3608 ?
HARRISBURG PA 17105-3608
For customer repair service, call 1-800-526-5136.
6. REVISION SUMMARY
Since the previous version of this document, the
following changes were made:
? Removed logos from graphics.
? Removed trademark references to ratchet.
? Updated crimp height inspection and comparator
TERMINAL
NUMBER
60445
60500
60501
60553
60556
WIRE SIZE
AWG (Max)
20
(2) 22
CRIMP SECT
(Wire Size
Marking)
24 - 20
2 - 26
2 - 22
CRIMP
HEIGHT DIM.
“A”
0.94 [.037]
sourcing information.
? Updated logo and format to corporate
requirements.
Figure 4
C. Ratchet Inspection
Obtain a 0.025 [.001] shim that is suitable for checking
the clearance between the bottoming surfaces of the
crimping dies. Proceed as follows:
1. Select a terminal and maximum size wire for the
hand tool.
Rev C
3 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 90090-3 | ASSY SAHT |
| 90101-3 | ASSY SAHT |
| 90120 | DOUBLE ACTION HAND TOOL BLACK |
| 90121 | SADAHT C CRIMP 12-18 |
| 90136-1 | TOOL HAND CERTI-CRIMP II W/DIES |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90075-1005 | 制造商:Molex 功能描述:WE PLUG HSG 6/6 9 HSG 6/6 900751005 |
| 90075-1033 | 制造商:MOLEX 功能描述:WE PLUG HSG 6/4 900751033 制造商:Molex 功能描述:WE PLUG HSG 6/4 9007 UG HSG 6/4 900751033 |
| 90075-1059 | 制造商:Molex 功能描述:HOUSING 8/8 W/O LUG W/O LUG 900751059 |
| 9007550 | 制造商:SYLVANIA 功能描述:STRIPLIGHT 221MM 30W CLEAR |
| 9007551 | 制造商:SYLVANIA 功能描述:STRIPLIGHT 221MM 30W OPAL |
发布紧急采购，3分钟左右您将得到回复。