- 您现在的位置：买卖IC网 > Datasheet目录611 > 90274-2 (TE Connectivity)SAHT F CRIMP Datasheet资料下载
参数资料
| 型号： | 90274-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | SAHT F CRIMP |
| 标准包装： | 1 |
| 系列： | Certi-Crimp, AMPMODU MOD I |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，18-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | 102103-3-ND - CONN RCPT CONTACT 22-18AWG TIN 102103-2-ND - CONN RCPT CONTACT 22-18AWG GOLD 102104-1-ND - CONN CONTACT 18-22AWG CRIMP 102104-3-ND - CONN RCPT 22-18AWG CRIMP TIN 102104-2-ND - CONN TERM RECEPT 18-22AWAG 30AU |
408-7594
Make sure all pivot points and bearing surfaces are
protected with a thin coat of any good SAE 20 motor
oil. Do NOT oil excessively. When the tool is not in
use, keep the handles closed to prevent objects from
becoming lodged between the dies, and store the tool
in a clean, dry area.
5.2. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool and/or be supplied to the
supervisory personnel responsible for the tool. Though
recommendations call for at least one inspection a
month, the inspection frequency should be based on
the amount of use, ambient working conditions,
operator training and skill, and established company
standards. These inspections should be performed in
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the chart,
the tool is considered dimensionally correct. If not,
return the tool for evaluation and repair (refer to
Section 6, REPLACEMENT AND REPAIR).
Position Point on
Center of Wire
Barrel Opposite
Seam
the following sequence:
A. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the tool (handles partially closed) into a
Modified
Anvil
“A”
±0.05
[±.002]
suitable degreaser that will not affect paint or plastic
material.
2. Make certain all retaining pins are in place and
are secured with the proper retaining rings. If
replacements are necessary, refer to Figure 5.
3. Close the tool handles until the ratchet releases,
and then allow the handles to open freely. If they do
CONTACT
NUMBER
(LP)
87026
87027
102103
102104
WIRE SIZE
AWG (Max)
20
18
CRIMP SECT
(Wire Size
Marking)
22-20
18
CRIMP
HEIGHT DIM.
“A”
0.84 [.033]
1.07 [.042]
not open quickly and fully, then the spring is
defective and must be replaced (see Section 6,
REPLACEMENT AND REPAIR).
4. Inspect the head assembly, with special
emphasis on checking for worn, cracked, or broken
crimping dies. If damage to any part of the head is
evident, return the tool for evaluation and repair
(see Section 6, REPLACEMENT AND REPAIR).
B. Crimp Height Inspection
Crimp height inspection is performed through the
use of a micrometer with a modified anvil,
commonly referred to as a crimp height comparator. ?
TE does not market crimp height comparators.
Refer to Instruction Sheet 408-7424 for detailed
information on obtaining and using a crimp height
comparator.
Proceed as follows:
1. Refer to the chart in Figure 4 and select a contact
and a wire (maximum size) for each crimp section.
2. Refer to Section 3, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
Rev B
Figure 4
C. Ratchet Inspection
Obtain a 0.025 [.001] shim that is suitable for checking
the clearance between the bottoming surfaces of the
crimping dies. Proceed as follows:
1. Select a contact and maximum size wire for the
hand tool.
2. Position the contact and wire between the
crimping dies, as described in Section 3,
CRIMPING PROCEDURE.
3. Holding the wire in place, squeeze the tool
handles together until the ratchet releases. Hold the
handles in this position, maintaining just enough
tension to keep the dies closed.
4. Check the clearance between the bottoming
surfaces of the crimping dies. If the clearance is
0.025 [.001] or less, the ratchet is satisfactory. If the
clearance exceeds 0.025 [.001], the ratchet is out of
adjustment and must be repaired.
3 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 90276-2 | HHHT PIDG PG FASTON 10-12 |
| 90280-1 | DIE PIDG 12-10 |
| 90294-1 | SAHT F CRIMP 22-26 |
| 90308-1 | SAHT LKG CLIP 031X.062 |
| 90313-2 | SAHT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 902743M | 制造商:DANAHER TOOL GROUP 功能描述:CHUCK KEY S2 |
| 902-745 | 功能描述:支架与垫片 Plastic Spcr .745 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90275 | 制造商:NTE 制造商全称:NTE Electronics 功能描述:1000V CERAMIC DISC |
| 902-750 | 功能描述:支架与垫片 Plastic Spcr .75 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 902-755 | 功能描述:支架与垫片 Plastic Spcr .755 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。