- 您现在的位置：买卖IC网 > Datasheet目录611 > 90280-1 (TE Connectivity)DIE PIDG 12-10 Datasheet资料下载
参数资料
| 型号： | 90280-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | DIE PIDG 12-10 |
| 标准包装： | 1 |
| 系列： | * |
| 配用： | 61198-4-ND - CONN RCPT FASTON 12-10AWG .250 |
408- 7563
A. Visual Inspection
Remove all lubrication and accumulated film by
immersing the dies in a commercial degreaser. Then:
to ensure quality and reliability of the dies. Order
replacement parts through your TE Representative, or
call 1--800--526--5142, or send a facsimile of your
purchase order to 1--717--986--7605, or write to:
1. Remove all lubrication and accumulated film
from the dies by immersing the dies in a suitable
commercial degreaser.
2. Make sure all die hardware and parts are
properly secured.
3. Carefully inspect die surfaces for wear, cracking,
pitting, or other obvious damage. Replace parts as
necessary before returning dies to service. See
Figure 4.
B. Gaging the Wire Barrel Crimping Chamber (Figure 3)
Figure 3 shows dimensions for manufacture of plug
gages needed to inspect the wire barrel crimping
chamber of each die assembly. TE Connectivity (TE)
does not make or market these gages. However,
gages may be purchased from:
GO
Diameter
Suggested Plug Gage Design
50.8 [2.00]
Min. Typ.
NO-- GO Element Must Not Pass
Through Crimping Chamber
NO-- GO
Diameter
Pennoyer--Dodge Company
6643--T San Fernando Road
Glendale, CA 91201
Gage crimping chamber using the following
procedures:
GO Element Must Pass
Through Crimping Chamber
1. Close dies until bottomed, and hold them in this
position.
2. Align the plug gage GO element with the
crimping chamber. Push the element straight into
the chamber, but do not force it. The GO element
must pass through the chamber.
CRIMPING
DIE NUMBER
90240--2
90248--2
GAGE ELEMENT DIAMETER
GO NO-- GO
3.52 [.1385] 3.64 [.1435]
1.59 [.0625] 1.71 [.0675]
3. Align the NO--GO element and try to insert it
straight into the crimping chamber. The NO--GO
element may begin entry as shown in Figure 3, but
must not pass through the chamber.
If dies conform dimensionally, lubricate them with a
thin coat of any good SAE 20 motor oil. If not, replace
the dies.
For additional information on plug gages, refer to
instruction sheet 408--7424.
6. REPLACEMENT AND REPAIR
Replacement parts are listed in Figure 4. Parts other
than those listed in Figure 4 should be replaced by TE
Rev B
90280--1 3.80 [.1495] 3.95 [.1555]
Figure 3
CUSTOMER SERVICE (38--35)
TYCO ELECTRONICS CORPORATION
P.O. BOX 3608
HARRISBURG, PA 17105--3608
For repair service, please contact a TE
Representative at 1--800--526--5136.
7. REVISION SUMMARY
S Updated document to corporate requirements
S New logo
3 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 90294-1 | SAHT F CRIMP 22-26 |
| 90308-1 | SAHT LKG CLIP 031X.062 |
| 90313-2 | SAHT |
| 90327-1 | SAHT TYPE VI |
| 90348-2 | DIE W/O 69710-1 8 F IS7918 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9028-010 WAF | 制造商:SMSC 功能描述: |
| 9028020000 | 制造商:Weidmuller 功能描述:DIE,MTR 300 -EA - Bulk 制造商:Weidmuller 功能描述:DIE MTR 300 |
| 902805 | 制造商:Mitutoyo Corporation 功能描述:STEM 9.5DIA. & NUT |
| 902-805 | 功能描述:支架与垫片 Plastic Spcr .805 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 902807-000 | 制造商:TE Connectivity 功能描述:3024-10-441116 |
发布紧急采购，3分钟左右您将得到回复。