- 您现在的位置：买卖IC网 > Datasheet目录611 > 90390-3 (TE Connectivity)DIE SET ULTRA-FASTONS 22-18 AWG Datasheet资料下载
参数资料
| 型号： | 90390-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/5页 |
| 文件大小： | 0K |
| 描述： | DIE SET ULTRA-FASTONS 22-18 AWG |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, Faston |
| 压接或电缆尺寸： | 18-22 AWG |
| 压接手柄： | A28005-ND |
| 连接器类型： | 端子及连接件 |
| 产品目录页面： | 375 (CN2011-ZH PDF) |
| 配用： | 8-520335-1-ND - CONN RECEPT FAST 18-22AWG .187 8-520194-1-ND - CONN RECEPT FAST 18-22AWG .187 8-520084-1-ND - CONN RECEPT FAST 18-22AWG .110 8-520182-1-ND - CONN FAST RECEPT 18-22 AWG .187 8-520103-1-ND - CONN TAB ULTRA FAST 18-22 AWG 8-520184-1-ND - CONN FAST RECEPT 18-22 AWG .250 8-520129-1-ND - CONN FAST FLG RCPT 18-22AWG .250 8-520273-1-ND - 110 ULTRA-FAST RCPT 22-18 TPBR 8-520264-1-ND - CONN RECEPT FAST 18-22 AWG .250 8-520337-1-ND - CONN RCPT FLG FAST 18-22AWG .187 更多... |
| 相关产品： | A28005-ND - HAND CRIMP TOOL/FASTOS(W/O DIES) |
| 其它名称： | 90390-3-ND A28007 |
Crimping Die Assemblies
90390-3 and 90391-3
Instruction Sheet
408-9279
28 JUN 13 Rev E
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Crimp Symbol
(Dot Code)
Die Retaining
Screw
Upper Die
Assembly
(Crimper
the anvil, while the 90391-3 die assembly has a blue
color dot on the crimper and the anvil. The color
coding on the die assembly corresponds to the color
coding on translucent insulation of the Ultra-Fast
FASTON terminal for easier identification when
crimping.
3. INSTALLATION
Determine the part number of the terminal you are
crimping, then refer to the table in Figure 2 and select
the appropriate die assembly. Install dies as described
below.
Lower Die
Assembly
(Anvil)
Set Screw
Figure 1
Color Code
3.1. Installing Lower Die Assembly
1. Squeeze the tool handles together until they
bottom. Then allow them to open fully.
2. Hold the hand tool frame so that the back of
the tool is facing you and note the socket head
screw located in the lower die platform. See
Figure 3.
3. Slide the lower die onto the lower platform,
ensuring that the drilled holes on the side of the
lower die line up with the socket head screw.
1. INTRODUCTION
Platform Crimping Die Assemblies 90390-3 and
90391-3 are used in Platform Hand Tool Frame
58078-3 (Instruction Sheet 408-6976). The die
NOTE
i
If the lower die will not seat on the lower die
platform with the drilled hole aligned with the socket
head screw, use the hex wrench to turn the screw
either in or out until the set screw does not protrude
from either side of the lower tool jaw.
assemblies crimp the Ultra-Fast Fully Insulated
FASTON* Terminals listed in Figure 2. Read These
instructions before using the Platform Hand Tool
Frame and Platform Crimping Dies.
4. With the lower die in place, turn the socket
head screw (on the die platform) clockwise until
snug. Do NOT overtighten.
NOTE
i
Dimensions are in millimeters [with inch
equivalents in brackets]. Figures are for
identification only and are not drawn to scale.
3.2. Installing Upper Die Assembly
1. Remove the die retaining screw from the die
assembly.
2. Position the upper die in upper die platform of
Reasons for reissue are provided in Section 7,
REVISION SUMMARY.
2. DESCRIPTION
Each die assembly consists of an upper die (crimper)
and a lower die (anvil), a retaining screw (on the upper
die), and a hex wrench for securing the lower die to
the platform of the hand tool frame.
The die assemblies are identified by part numbers,
color dot codes, and applicable wire range
designations. See Figure 1. The 90390-3 die
assembly has a red color dot on both the crimper and
the tool. Thread the die retaining screw through
the mounting hole in the top of tool and tighten
the screw until it is snug but NOT secured.
3. While guiding the upper die into alignment with
the lower die, slowly close the tool handles until
the dies bottom.
4. Tighten the upper die retaining screw until the
die is secure.
5. Squeeze the tool handles together until the
ratchet releases. Allow the tool handles to open
fully. The tool is now ready for use.
?2013 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
1 of 5
TE logo is a trademark.
*Trademark. Other products, logos, and company names might be trademarks of their respective owners.
visit our website at www.te.com
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| 90431-1 | TOOL CERTI-CRIMP HAND 20-24AWG |
| 904379-1 | CONNECTOR KIT ULTRA ATA |
| 90471-1 | EXTRACTION TOOL |
| 904800-1 | SEATING TL. ASSY 2MMHM V.COAX |
| 90575-2 | TOOL DIESET 14-20AWG COM-MATE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90390-3 CAL | 制造商:TE Connectivity 功能描述:CALIBRATED - Tools, Dies, Crimp Size:22AWG to 16AWG, For Use With:Tyco 58078-3 H 制造商:TE Connectivity / AMP 功能描述:CALIBRATED - Tools, Dies, Crimp Size:22AWG to 16AWG, For Use With:Tyco 58078-3 Hand Crimp Too |
| 90390-3 CAL D | 制造商:TE Connectivity 功能描述:CALIBRATED W/DATA - Tools, Dies, Crimp Size:22AWG to 16AWG, For Use With:Tyco 58 制造商:TE Connectivity / AMP 功能描述:CALIBRATED W/DATA - Tools, Dies, Crimp Size:22AWG to 16AWG, For Use With:Tyco 58078-3 Hand Crimp Too |
| 90390-3 CAL DU | 制造商:TE Connectivity 功能描述:CALIBRATED W/ DATA & UNCERTAINTIES - Tools, Dies, Crimp Size:22AWG to 16AWG, For 制造商:TE Connectivity / AMP 功能描述:CALIBRATED W/ DATA & UNCERTAINTIES - Tools, Dies, Crimp Size:22AWG to 16AWG, For Use With:Tyco 58078-3 Hand Crimp Too |
| 90390-3 | 制造商:TE Connectivity 功能描述:Crimping Tool Die Set for Faston Recep |
| 90391-3 | 功能描述:冲压机与冲模 DIE SET 16-14 AWG RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。