- 您现在的位置：买卖IC网 > Datasheet目录611 > 90652-1 (TE Connectivity)PRO-CRIMPER ASSY MULTILOCK Datasheet资料下载
参数资料
| 型号： | 90652-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/6页 |
| 文件大小： | 0K |
| 描述： | PRO-CRIMPER ASSY MULTILOCK |
| 标准包装： | 5 |
| 系列： | Pro-Crimper III 型，多锁系列 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，18-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | 175062-2-ND - 040 MULTILOCK REC CONT. L/P |
PRO- CRIMPER III Hand Crimping Tool Assembly 90652- 1
408- 9853
Chamfer
Wire Crimper
Offset
Nut
Insulation
Crimper
Locator Assembly
Tool Frame
Die Retaining
Pins
Wire Anvil
Insulation Anvil
Chamfer
Die Retaining Screws
Figure 2
2. DESCRIPTION (Figures 1 and 2)
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with two
crimping sections.
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
Attached to the outside of the frame is a locator
assembly, which contains a locator, a spring retainer,
and a contact support.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame. A
nut is used on the upper die retaining screw to hold
the locator assembly in place.
3. INSTALLATION AND REMOVAL OF DIE SET
AND LOCATOR ASSEMBLY (Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do
NOT tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two die retaining pins.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
10. Place the nut onto the end of the long screw
and tighten the nut enough to hold the locator
assembly in place, while still allowing the locator to
slide up and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the
four die retaining pins, and slide the anvils and
crimpers out of the tool jaws.
2 of 6
Tyco Electronics Corporation
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 90654-2 | PROCRIMPER DIE ASSY MULTILOCK |
| 90682-2 | PROCRIMPER DIE ASSY DYNAMIC |
| 90683-2 | PROCRIMPER DIE ASSY DYNAMIC |
| 90684-2 | PROCRIMPER DIE ASSY DYNAMIC |
| 90687-6 | SEATING TOOLS FOR MICRO-STRIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90652-2 | 功能描述:以太网和电信连接器 PROCRIMP DIE ASSEMB RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: |
| 906-525 | 功能描述:支架与垫片 Plastic Spcr .525 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90653 | 制造商:Brady Corporation 功能描述: |
| 906-530 | 功能描述:支架与垫片 Plastic Spcr .53 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90653-1 | 功能描述:折皱器 PRO-CRIMPER ASSY MULTILOCK RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。