- 您现在的位置：买卖IC网 > Datasheet目录611 > 90652-1 (TE Connectivity)PRO-CRIMPER ASSY MULTILOCK Datasheet资料下载
参数资料
| 型号： | 90652-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | PRO-CRIMPER ASSY MULTILOCK |
| 标准包装： | 5 |
| 系列： | Pro-Crimper III 型，多锁系列 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，18-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | 175062-2-ND - 040 MULTILOCK REC CONT. L/P |
i
PRO- CRIMPER III Hand Crimping Tool Assembly 90652- 1
4. CONTACT SUPPORT ADJUSTMENT (Figure 3)
NOTE The contact support is preset prior to shipment,
but minor adjustment may be necessary.
i
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
NOTE The ratchet has detents that create audible clicks
as the tool handles are closed.
i
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame
5. Move the contact support as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
408- 9853
contact is still being bent during crimping, repeat
the adjustment procedure.
5. CRIMPING PROCEDURE
NOTE This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be
verified as specified in Figure 4. Refer to
Section 6, CRIMP HEIGHT INSPECTION , and
Section 7, RATCHET (Crimp Height)
ADJUSTMENT, to verify crimp height before
using the tool to crimp desired contacts and wire
sizes.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact — insulation barrel first — through the front
of the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
face the top of the tool. Place the contact up into
the nest so that the movable locator drops into the
slot in the contact. Refer to Figure 3. Butt the front
end of the wire barrel against the movable locator.
Contact
Support
Locator
Back of Tool
(Wire Side)
Adjustment
Screw for
Contact
Support
Wire
Figure 3
Contact
(Typ)
Locator in
Wire Stop
Slot
Strip
Length
Wire Inserted
to Stop
Rev C
Tyco Electronics Corporation
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 90654-2 | PROCRIMPER DIE ASSY MULTILOCK |
| 90682-2 | PROCRIMPER DIE ASSY DYNAMIC |
| 90683-2 | PROCRIMPER DIE ASSY DYNAMIC |
| 90684-2 | PROCRIMPER DIE ASSY DYNAMIC |
| 90687-6 | SEATING TOOLS FOR MICRO-STRIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90652-2 | 功能描述:以太网和电信连接器 PROCRIMP DIE ASSEMB RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: |
| 906-525 | 功能描述:支架与垫片 Plastic Spcr .525 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90653 | 制造商:Brady Corporation 功能描述: |
| 906-530 | 功能描述:支架与垫片 Plastic Spcr .53 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90653-1 | 功能描述:折皱器 PRO-CRIMPER ASSY MULTILOCK RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。