- 您现在的位置：买卖IC网 > Datasheet目录611 > 90684-2 (TE Connectivity)PROCRIMPER DIE ASSY DYNAMIC Datasheet资料下载
参数资料
| 型号： | 90684-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | PROCRIMPER DIE ASSY DYNAMIC |
| 标准包装： | 25 |
| 系列： | * |
| 其它名称： | Q2338535 Q3791792 |
PRO- CRIMPER III Hand Crimping Tool Assembly 90684- 1
4. CONTACT SUPPORT ADJUSTMENT (Figure 3 )
5. CRIMPING PROCEDURE
408- 9934
NOTE The contact support is preset prior to shipment,
but minor adjustment may be necessary.
i
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
NOTE
i
This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be
verified as specified in Figure 4. Refer to
Section 6, CRIMP HEIGHT INSPECTION, and
Section 7, RATCHET ADJUSTMENT, to verify
crimp height before using the tool to crimp
desired contacts and wire sizes.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
NOTE The ratchet has detents that create audible clicks
as the tool handles are closed.
i
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact — insulation barrel first — through the front
of the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
face the top of the tool. Place the contact up into
the nest so that the movable locator drops into the
slot in the contact. Refer to Figure 3. Butt the front
end of the wire barrel against the movable locator.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat
the adjustment procedure.
Contact
Locator
Support
CAUTION
!
Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do
NOT attempt to crimp an improperly positioned
contact.
Adjustment
Screw for
Contact Support
Back of Tool
(Wire Side)
Wire
Contact
(Typ)
Locator in
Wire Stop Slot
Strip
Length
Wire Inserted
to Stop
Figure 3
Rev C
Tyco Electronics Corporation
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 90687-6 | SEATING TOOLS FOR MICRO-STRIP |
| 90717-2 | TOOL SAHT 26-30 MINI UMNL |
| 90752-1 | SEATING TOOL ASSY H.M. 110 PIN |
| 90754-3 | SEATING TOOL ASSY HM 95 PIN |
| 90756-1 | SEATING TOOL ASSY H.M. 55 PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 906-845 | 功能描述:支架与垫片 Plastic Spcr .845 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90685 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:2803 |
| 906-850 | 功能描述:支架与垫片 Plastic Spcr .85 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90685-1 | 制造商:TE Connectivity 功能描述:GUARD - Bulk |
| 906-855 | 功能描述:支架与垫片 Plastic Spcr .855 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。