- 您现在的位置：买卖IC网 > Datasheet目录612 > 90759-2 (TE Connectivity)DIE SET FOR PRO-C III 22-20,18 Datasheet资料下载
参数资料
| 型号： | 90759-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | DIE SET FOR PRO-C III 22-20,18 |
| RoHS指令信息： | 90759-2 Statement of Compliance |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 18-22 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 产品目录页面： | 425 (CN2011-ZH PDF) |
| 配用： | 1-770988-1-ND - CONTACT SKT 18-22AWG MINI-UMNL A97677-ND - CONN PIN 18-22AWG M-U MNL 30GOLD A106258-ND - CONTACT PIN 18-22AWG MINI-UMNL 170366-4-ND - CONN SOCKET MINI UMNL 18-22AWG A33329-ND - CONN SOCKET 18-22AWG GOLD CRIMP A32446-ND - CONN PIN 18-22AWG GOLD CRIMP A32016-ND - CONN SOCKET 18-22AWG GOLD CRIMP A32015-ND - CONN PIN 18-22AWG GOLD CRIMP A97690-ND - CONN SOCKET 18-22AWG GOLD CRIMP A28813-ND - CONN SOCKET 18-22AWG GOLD CRIMP 更多... |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A30040 |
408- 9962
4. CONTACT SUPPORT ADJUSTMENT (Figure 3 )
5. CRIMPING PROCEDURE
NOTE The contact support is preset prior to shipment,
but minor adjustment may be necessary.
i
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
NOTE
i
This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be
verified as specified in Figure 4. Refer to
Section 6, CRIMP HEIGHT INSPECTION, and
Section 7, RATCHET ADJUSTMENT, to verify
crimp height before using the tool to crimp
desired contacts and wire sizes.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
NOTE The ratchet has detents that create audible clicks
as the tool handles are closed.
i
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact — insulation barrel first — through the front
of the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
face the top of the tool. Place the contact up into
the nest so that the movable locator drops into the
slot in the contact. Refer to Figure 3. Butt the front
end of the wire barrel against the movable locator.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat
the adjustment procedure.
Contact
Locator
Support
CAUTION
!
Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do
NOT attempt to crimp an improperly positioned
contact.
Adjustment
Screw for
Contact Support
Back of Tool
(Wire Side)
Wire
Contact
(Typ)
Locator in
Wire Stop Slot
Strip
Length
Wire Inserted
to Stop
Figure 3
Rev C
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 90800-2 | DIE SET HI-DEN D-SUB CRIMP CONT |
| 90869-2 | DIE SET 24-18 AWG USE WITH A9996 |
| 90870-2 | DIE SET FOR PROC III 30-28,26-24 |
| 90871-2 | DIE SET 20-14 AWG USE WITH A9996 |
| 90872-1 | TOOL CRIMP .093 AWG 24 W/DIE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 907-595 | 功能描述:支架与垫片 Plastic Spcr .595 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 907-5M NC032 | 功能描述:M12 DIE CAST 4PORT 2SIG 制造商:alpha wire 系列:- 零件状态:在售 配件类型:触动器盒 颜色:黑色 特性:- 配套使用产品/相关产品:圆形连接器 材料:锌压铸件 外壳尺寸 - 插件:M12 标准包装:1 |
| 907-5MM | 功能描述:支架与垫片 Plastic Spcr 5mm Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 9075Z | 制造商:Stancor 功能描述: |
| 9076.99.N078 | 制造商:HUBER+SUHNER 功能描述:INTERCONNECT KIT |
发布紧急采购，3分钟左右您将得到回复。