- 您现在的位置：买卖IC网 > Datasheet目录612 > 90870-2 (TE Connectivity)DIE SET FOR PROC III 30-28,26-24 Datasheet资料下载
参数资料
| 型号： | 90870-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/6页 |
| 文件大小： | 0K |
| 描述： | DIE SET FOR PROC III 30-28,26-24 |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 24-30 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 产品目录页面： | 240 (CN2011-ZH PDF) |
| 配用： | A14048-ND - CONN SOCKET 24-30AWG TIN CRIMP A14016-ND - CONN PIN 24-30AWG TIN CRIMP |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9956 |
PRO- CRIMPER III Hand Crimping Tool Assembly 90870- 1
408- 9965
Chamfer
Wire Crimper
Offset
Nut
Locator
Insulation
Crimper
Locator
Assembly
Tool Frame
Die Retaining
Pins
Wire Anvil
Insulation
Anvil
Chamfer
Die Retaining
Screws
Figure 2
Attached to the outside of the frame is a locator
assembly, which contains a locator, a spring retainer,
and a contact support.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame. A
nut is used on the upper die retaining screw to hold
the locator assembly in place.
3. INSTALLATION AND REMOVAL OF DIE SET
AND LOCATOR ASSEMBLY (Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two die retaining pins.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
10. Place the nut onto the end of the long screw
and tighten the nut enough to hold the locator
assembly in place, while still allowing the locator to
slide up and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the
four die retaining pins, and slide the anvils and
crimpers out of the tool jaws.
2 of 6
Tyco Electronics Corporation
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 90871-2 | DIE SET 20-14 AWG USE WITH A9996 |
| 90872-1 | TOOL CRIMP .093 AWG 24 W/DIE |
| 91002-1 | TOOL INSERTION .062 & .093 CONN |
| 91016-2 | TOOL HAND SPIRAL PIN INSERTION |
| 91017-3 | TOOL AMP-INCERT TAB EXTRACTION |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 908-7028-2HZ | 制造商:Amphenol RF 功能描述:MALE CONTACT |
| 90870314 | 制造商:Western Auto 功能描述: |
| 908-705 | 功能描述:支架与垫片 Plastic Spcr .705 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 908-710 | 功能描述:支架与垫片 Plastic Spcr .71 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 908710001 | 制造商:MOLEX 功能描述: |
发布紧急采购，3分钟左右您将得到回复。