- 您现在的位置：买卖IC网 > Datasheet目录612 > 90870-2 (TE Connectivity)DIE SET FOR PROC III 30-28,26-24 Datasheet资料下载
参数资料
| 型号： | 90870-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | DIE SET FOR PROC III 30-28,26-24 |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 24-30 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 产品目录页面： | 240 (CN2011-ZH PDF) |
| 配用： | A14048-ND - CONN SOCKET 24-30AWG TIN CRIMP A14016-ND - CONN PIN 24-30AWG TIN CRIMP |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9956 |
i
PRO- CRIMPER III Hand Crimping Tool Assembly 90870- 1
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop,
as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
NOTE The crimped contact may stick in the crimping
area, but the contact can be easily removed by
pushing downward on the top of the locator (see
Figure 3).
7. Check the contact’s crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, RATCHET ADJUSTMENT.
6. CRIMPHEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp--height comparator. Tyco
Electronics does not manufacture or market
crimp--height comparators. Detailed information on
obtaining and using crimp--height comparators can be
found in instruction sheet 408--7424.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
Position Point
on Center of
Wire Barrel
Opposite
Seam
Modified Anvil “A”
408- 9965
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
Screwdriver
Ratchet
Adjustment
Wheel
Lockscrew
(Typ)
Figure 5
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher--numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower--numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
Wire Size
AWG (Max)
28
24
Crimp Section
(Wire Size Marking)
30--28
26--24
Figure 4
Crimp Height
Dimension A
0.58 [.023]
0.64 [.025]
8. MAINTENANCE
Ensure that the tool and dies are clean by wiping
them with a clean, soft cloth. Remove any debris with
a clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in
the crimping dies, and store in a clean, dry area.
4 of 6
Tyco Electronics Corporation
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 90871-2 | DIE SET 20-14 AWG USE WITH A9996 |
| 90872-1 | TOOL CRIMP .093 AWG 24 W/DIE |
| 91002-1 | TOOL INSERTION .062 & .093 CONN |
| 91016-2 | TOOL HAND SPIRAL PIN INSERTION |
| 91017-3 | TOOL AMP-INCERT TAB EXTRACTION |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 908-7028-2HZ | 制造商:Amphenol RF 功能描述:MALE CONTACT |
| 90870314 | 制造商:Western Auto 功能描述: |
| 908-705 | 功能描述:支架与垫片 Plastic Spcr .705 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 908-710 | 功能描述:支架与垫片 Plastic Spcr .71 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 908710001 | 制造商:MOLEX 功能描述: |
发布紧急采购，3分钟左右您将得到回复。