- 您现在的位置：买卖IC网 > Datasheet目录612 > 90871-2 (TE Connectivity)DIE SET 20-14 AWG USE WITH A9996 Datasheet资料下载
参数资料
| 型号： | 90871-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | DIE SET 20-14 AWG USE WITH A9996 |
| 标准包装： | 10 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 14-20 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 产品目录页面： | 241 (CN2011-ZH PDF) |
| 配用： | 770144-6-ND - CONN SOCKET 20-14AWG CRIMP TIN A25779-ND - CONN SOCKET 14-20AWG GOLD CRIMP A25778-ND - CONN PIN 14-20AWG GOLD CIRMP A14097-ND - CONN SOCKET 14-20AWG TIN CRIMP A14099-ND - CONN PIN 14-20AWG TIN CRIMP |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9953 |
408-9966
NOTE
i
The ratchet has detents that create audible clicks
as the tool handles are closed.
Adjustment, to verify crimp height before using the
tool to crimp desired contacts and wire sizes.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire to
the length indicated in Figure 1, taking care not to nick
NOTE
i
attempt to crimp an improperly positioned contact.
3. Place a contact with wire into the proper nest and
close the tool handles until the ratchet reaches the
sixt# click, or until the contact support touches the
contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to eliminate
the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat the
adjustment procedure.
5. CRIMPING PROCEDURE
This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be verified
as specified in Figure 4. Refer to Section 6, Crimp
Height Inspection, and Section 7, RATCHET
or cut wire strands. Select an applicable contact and
identify the appropriate crimp section according to the
wire size markings on the tool. Refer to Figure 3 and
proceed as follows:
1. Hold the tool so that the back (wire side) is facing
you. Squeeze tool handles together and allow them
to open fully.
2. Holding the contact by the mating end, insert the
contact - insulation barrel first - through the front of
the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of the
contact is on the locator side of the tool, and so that
the open "U" of the wire and insulation barrels face
the top of the tool. Place the contact up into the nest
so that the movable locator drops into the slot in the
contact. Refer to Figure 3. Butt the front end of the
wire barrel against the movable locator.
CAUTION Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do not
!
Adjustment
Screw for Contact
Support
Contact
Support
Locator
Back of Tool
(Wire Side)
Rev C
Wire
Figure 3
Contact
(Typ)
Locator
in Wire
Stop Slot
Strip
Length
Wire
Inserted
to Stop
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 90872-1 | TOOL CRIMP .093 AWG 24 W/DIE |
| 91002-1 | TOOL INSERTION .062 & .093 CONN |
| 91016-2 | TOOL HAND SPIRAL PIN INSERTION |
| 91017-3 | TOOL AMP-INCERT TAB EXTRACTION |
| 91018-1 | AMP-INCERT TAB EXTRACTION TOOL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90871-2001 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. /INDIR FEM. 2.5 7CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 90871-2501 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. /INDIR FEM. 2.5 8CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 908712MMX50M | 制造商:3M Electronic Products Division 功能描述:Non-woven Double Coated Tape, 12mm |
| 90871-3001 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. /INDIR FEM. 2.5 9CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 90871-3501 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. INDIR FEM. 2.5 10CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
发布紧急采购，3分钟左右您将得到回复。