- 您现在的位置：买卖IC网 > Datasheet目录612 > 90871-2 (TE Connectivity)DIE SET 20-14 AWG USE WITH A9996 Datasheet资料下载
参数资料
| 型号： | 90871-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | DIE SET 20-14 AWG USE WITH A9996 |
| 标准包装： | 10 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 14-20 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 产品目录页面： | 241 (CN2011-ZH PDF) |
| 配用： | 770144-6-ND - CONN SOCKET 20-14AWG CRIMP TIN A25779-ND - CONN SOCKET 14-20AWG GOLD CRIMP A25778-ND - CONN PIN 14-20AWG GOLD CIRMP A14097-ND - CONN SOCKET 14-20AWG TIN CRIMP A14099-ND - CONN PIN 14-20AWG TIN CRIMP |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9953 |
408-9966
4. Hold the contact in position and squeeze the tool
handles together until ratchet engages sufficiently to
hold the contact in position. Do NOT deform
insulation barrel or wire barrel.
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop, as
shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles to
open and remove crimped contact.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)
1. Remove the lockscrew from the ratchet
adjustment wheel.
NOTE
i
The crimped contact may stick in the crimping area,
but the contact can be easily removed by pushing
downward on the top of the locator (see Figure 3).
2. With a screwdriver, adjust the ratchet wheel from
the locator side of the tool.
Screwdriver
7. Check the contact's crimp height as described in
Section 6, Crimp Height Inspection. If necessary,
adjust the crimp height as described in Section 7,
RATCHET ADJUSTMENT.
6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp-height comparator. TE does not
manufacture or market crimp-height comparators.
Detailed information on obtaining and using crimp-
height comparators can be found in instruction sheet
408-7424.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
Ratchet
Adjustment
Wheel
Lockscrew
(Typ)
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
Figure 5
Position Point
on Center of
Wire Barrel
Opposite
Seam
Modified Anvil
3. Observe the ratchet adjustment wheel. If a tighter
crimp is required, rotate the adjustment wheel
COUNTERCLOCKWISE to a higher-numbered
setting. If a looser crimp is required, rotate the
adjustment wheel CLOCKWISE to a lower-
numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
WIRE SIZE
AWG (Max)
18
14
CRIMP SECTION
(Wire Size Marking)
20-18
16-14
CRIMP HEIGHT
DIMENSION “A”
1.07 [.042]
1.45 [.057]
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
Figure 4
Rev C
4 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 90872-1 | TOOL CRIMP .093 AWG 24 W/DIE |
| 91002-1 | TOOL INSERTION .062 & .093 CONN |
| 91016-2 | TOOL HAND SPIRAL PIN INSERTION |
| 91017-3 | TOOL AMP-INCERT TAB EXTRACTION |
| 91018-1 | AMP-INCERT TAB EXTRACTION TOOL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90871-2001 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. /INDIR FEM. 2.5 7CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 90871-2501 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. /INDIR FEM. 2.5 8CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 908712MMX50M | 制造商:3M Electronic Products Division 功能描述:Non-woven Double Coated Tape, 12mm |
| 90871-3001 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. /INDIR FEM. 2.5 9CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 90871-3501 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. INDIR FEM. 2.5 10CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
发布紧急采购，3分钟左右您将得到回复。