- 您现在的位置：买卖IC网 > Datasheet目录612 > 90872-1 (TE Connectivity)TOOL CRIMP .093 AWG 24 W/DIE Datasheet资料下载
参数资料
| 型号： | 90872-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP .093 AWG 24 W/DIE |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III，商用 0.093" |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，18-24 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 241 (CN2011-ZH PDF) |
| 配用： | A25776-ND - CONN SOCKET 18-24AWG GOLD CRIMP A25775-ND - CONN PIN 18-24AWG GOLD CRIMP A14096-ND - CONN SOCKET 18-24AWG TIN CRIMP A14098-ND - CONN PIN 18-24AWG TIN CRIMP |
| 其它名称： | A9817 |
408-9967
CAUTION
!
Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do
NOT attempt to crimp an improperly positioned
contact.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do
NOT deform insulation barrel or wire barrel.
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop,
as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until the ratchet releases. Allow the tool
handles to open and remove crimped contact.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If
the crimp height conforms to that shown in the
table, the tool is considered dimensionally
correct. If not, the tool must be adjusted. Refer to
Section 7, RATCHET ADJUSTMENT.
7. RATCHET ADJUSTMENT
1. Remove the lockscrew from the ratchet
NOTE
i
The crimped contact may stick in the crimping area,
but the contact can be easily removed by pushing
downward on the top of the locator (see Figure 3). ?
?
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
3. Observe the ratchet adjustment wheel. If a
7. Check the contact’s crimp height as described
in Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described
in Section 7, RATCHET ADJUSTMENT.
6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp--height comparator. Tyco
Electronics does not manufacture or market crimp--
height comparators. Detailed information on obtaining
and using crimp--height comparators can befound in
instruction sheet 408-7424.
Position ?
Point on ?
Center of ?
Wire Barrel ?
Opposite ?
Seam
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a higher-
numbered setting. If a looser crimp is required,
rotate the adjustment wheel CLOCKWISE to a
lower-numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace
and secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
Screwdriver
Modified ?
Anvil
±.05 [.002]
Ratchet ?
Adjustment ?
Wheel
Wire Size
AWG (Max)
22
18
Crimp Section
(Wire Size Marking)
24-22
20-18
Crimp Height
Dim. “A”
.81
[.032]
1.02
[.040]
Lockscrew ?
(Typ)
Figure 5
Figure 4
Rev D
4 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 91002-1 | TOOL INSERTION .062 & .093 CONN |
| 91016-2 | TOOL HAND SPIRAL PIN INSERTION |
| 91017-3 | TOOL AMP-INCERT TAB EXTRACTION |
| 91018-1 | AMP-INCERT TAB EXTRACTION TOOL |
| 91018-2 | AMP-INCERT TAB EXTRACTION TOOL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90872-1001 | 功能描述:集管和线壳 5mm Rast 2.5 F-Direc -Direct K Nat 3Ckt RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 90872-2 | 功能描述:冲压机与冲模 DIE SET 24-18 .093 PRO CRIMP RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 908-725 | 功能描述:支架与垫片 Plastic Spcr .725 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 908725-000 | 制造商:TE Connectivity 功能描述:PTD-75-M-02 |
| 908725MMX50M | 制造商:3M Electronic Products Division 功能描述:Tape 9087 25 mm x 50 m |
发布紧急采购，3分钟左右您将得到回复。