- 您现在的位置：买卖IC网 > PDF目录18549 > 90872-2 (TE Connectivity)DIE SET 24-18 AWG USE WITH A9996 PDF资料下载
参数资料
| 型号： | 90872-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/6页 |
| 文件大小： | 0K |
| 描述： | DIE SET 24-18 AWG USE WITH A9996 |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 18-24 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 产品目录页面： | 241 (CN2011-ZH PDF) |
| 配用： | A25776-ND - CONN SOCKET 18-24AWG GOLD CRIMP A25775-ND - CONN PIN 18-24AWG GOLD CRIMP A14096-ND - CONN SOCKET 18-24AWG TIN CRIMP A14098-ND - CONN PIN 18-24AWG TIN CRIMP |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9952 |
408-9966
Nut
Locator
Chamfer
Wire
Crimper
Offset
Wire Anvil
Insulation
Crimper
Locator
Assembly
Tool Frame
Die Retaining
Pins
Insulation
Anvil
Chamfer
Die Retaining
Screw
Die Retaining
Screw
Figure 2
Die retaining pins and die retaining screws are used to
position and secure the dies in the tool frame. A nut is
used on the upper die retaining screw to hold the
locator assembly in place.
3. INSTALLATION AND REMOVAL OF DIE SET AND
LOCATOR ASSEMBLY (Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
8. Carefully close the tool handles, making sure that
the anvils and crimpers align properly. Continue
closing the tool handles until the ratchet in the tool
frame has engaged sufficiently to hold the anvils
and crimpers in place, then tighten both die
retaining screws.
9. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
10. Place the nut onto the end of the long screw and
tighten the nut enough to hold the locator assembly
in place, while still allowing the locator to slide up
and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the four
die retaining pins, and slide the anvils and crimpers
out of the tool jaws.
4. CONTACT SUPPORT ADJUSTMENT (Figure 3)
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two die retaining pins.
NOTE
i
The contact support is preset prior to shipment, but
minor adjustment may be necessary. ?
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
Rev C
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator assembly.
2 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| DLP0NSN900HL2L | CHOKE COIL COMMON MODE 100MA SMD |
| EEC2E705HQA403 | CAP FILM 7UF 250VAC QC TERM |
| 357B2102MAB251S22 | POT 1.0K OHM 20% SINGLE TURN |
| ASA-85.125MHZ-L-T3 | OSC 85.125 MHZ 3.3V SMD |
| IPC1FAD7/1L0Y | SWITCH PUSHBUTTON SPST 2A 125V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 908-725 | 功能描述:支架与垫片 Plastic Spcr .725 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 908725-000 | 制造商:TE Connectivity 功能描述:PTD-75-M-02 |
| 908725MMX50M | 制造商:3M Electronic Products Division 功能描述:Tape 9087 25 mm x 50 m |
| 908730 | 制造商:NORTH SAFETY PRODUCTS 功能描述:SAFETY SPEC T2400 CLEAR 制造商:North Safety Products USA 功能描述:SAFETY SPEC T2400 CLEAR 制造商:NORTH SAFETY PRODUCTS 功能描述:SAFETY SPEC T2400 CLEAR; Lens Colour:Clear; Frame Colour:Black; Safety Category:EN166.1.F; Lens Colour:Clear; Side Arms Colour:Black; Standard:EN166; Type:Tactile; Wavelength Max:390nm; Weight:0.022kg ;RoHS Compliant: NA |
| 908-730 | 功能描述:支架与垫片 Plastic Spcr .73 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。