- 您现在的位置：买卖IC网 > Datasheet目录612 > 91085-2 (TE Connectivity)TOOL MANUAL ARBOR PRESS Datasheet资料下载
参数资料
| 型号： | 91085-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | TOOL MANUAL ARBOR PRESS |
| 标准包装： | 1 |
| 工具类型： | 台式压机，框架 - 手动 |
| 适用于相关产品： | 随不同应用而各异 |
| 配用： | 856684-1-ND - CRIMPER ASSY ULTRA-D BACKSHEL 91411-2-ND - MASS TERMINATION APPLICATOR 122842-3-ND - TOOL CHAMP CRIMPER .8MM 36POS 122842-2-ND - TOOL CHAMP CRIMPER .8MM 68POS 768963-1-ND - TOOL 2MM CONN KIT FOR 91085-2 122842-1-ND - TOOL CHAMP CRIMPER 0.8MM ASSEMBY |
408- 7777
!
3. Secure the appropriate upper tooling to the tool
mount according to the instructions packaged with
the upper tooling.
4. Remove the tool stop from the base plate
subassembly (slide base).
5. Secure the appropriate lower tooling to the base
plate according to the instructions packaged with
the lower tooling.
6. Re--install the tool stop onto the base plate
subassembly.
7. To actuate the ram, pull down on the handle
until the upper tooling bottoms on the lower tooling.
To retract the ram, raise the handle.
CAUTION If the adjustment ring is NOT held in place when
the pinion is removed, the ram will drop and the
adjustment ring will slam onto the frame.
3. Rotate the handle to the desired position.
Ensure that the pinion rotates with the handle.
4. Push the pinion into the bore of the frame until it
engages the gear teeth in the ram.
5. Re--install the socket head cap screw and
washer. Re--install the plug button.
5. MAINTENANCE AND INSPECTION
5.1. Inspection
NOTE
i
Before beginning production, make sure that the
ram height is properly set according to Paragraph
4.1 and, if desired, adjust the handle according to
Paragraph 4.2.
It is recommended that the arbor frame assembly be
inspected according to Figure 3 immediately upon
arrival at your facility (and at regularly scheduled
intervals thereafter) to ensure that it has not been
damaged during handling.
4. RAM HEIGHT ADJUSTMENT
IMPORTANT: The ram height should be set before
adjusting the handle.
5.2. Lubrication
To prolong the useful life of the arbor frame assembly,
and to provide the smoothest operation, lubricate
monthly as follows:
4.1. Ram Height Adjustment
After installing the tooling assembly, it might be
necessary to adjust the height of the ram. Adjust the
ram height as follows:
NOTE
i
Though recommendations call for lubrication at
least once a month, the frequency should be
based on amount of use, working conditions, and
established company policies.
1. Determine the closed ram height dimension
required for the application.
2. Measure the distance between the bottom
surface of the upper tooling and the upper surface
of the lower tooling. Determine the direction (UP or
DOWN) that the ram must be moved.
3. Loosen the setscrew on the adjustment ring,
turn the adjustment ring clockwise to increase ram
height, or counterclockwise to decrease ram
height, then tighten the setscrew. Continue making
adjustments until the proper closed ram height
dimension is attained.
4.2. Adjusting the Handle
DANGER To avoid personal injury when adjusting the
handle, STAY CLEAR OF THE HANDLE.
Depending on position, the weight of the ram
could force the handle to rotate quickly.
1. Using the tip of a small flat--blade screwdriver,
remove the plug button. Remove the socket head
cap screw and washer from the bore of the frame.
2. Grasp the adjustment ring, and pull the pinion
(small diameter gear in bore of frame) out of the
frame just enough to disengage it from the gear
teeth in the ram. Allow the ram to drop slowly until
the adjustment ring rests on the frame.
2 of 3
1. Remove the two screws that secure the tool
mount to the ram. Remove the tool mount.
2. Remove the lower tooling.
3. Move the ram to the bottom of its stroke (the
adjustment ring should bottom on the base plate).
Note the position of the handle. Loosen the handle
adjustment knob sufficiently for the handle to slide
from its mounting hole. Remove the handle.
4. Using a small flat--blade screwdriver, turn the
spring plunger (refer to Figure 3 for location)
counterclockwise until it no longer contacts the
ram.
5. Grip the adjustment ring, and pull it upward,
then remove the ram.
6. Apply ANDEROL 757 ? lubricant, or equivalent,
to the gear teeth on the ram and to the bore of the
frame.
7. Re--assemble the ram into the bore with the
grooved side of ram aligned with the spring
plunger. Ensure that the gear teeth in the ram
engage the teeth of the pinion (small diameter gear
in bore of frame) so that the handle position will be
the same as noted in Step 2 when the adjustment
ring bottoms.
8. Turn the spring plunger clockwise until it
bottoms lightly on the ram, then back off one--half
of a turn.
Rev J
相关PDF资料 |
PDF描述 |
|---|---|
| 91093-1 | ET FFC |
| 91104-1 | EXTRACTION TOOL |
| 91111-1 | EXT TOOL ZERO ENTRY |
| 911149-7 | MINI PRESS 050 120P |
| 91117-1 | TOOL CLINCHING |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 910-855 | 功能描述:支架与垫片 Plastic Spcr .855 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 910-860 | 功能描述:支架与垫片 Plastic Spcr .86 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 910860-005 | 制造商: 功能描述: 制造商:MOOG INC 功能描述: 制造商:undefined 功能描述: |
| 910-865 | 功能描述:支架与垫片 Plastic Spcr .865 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 910-870 | 功能描述:支架与垫片 Plastic Spcr .87 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。