- 您现在的位置：买卖IC网 > Datasheet目录612 > 91293-1 (TE Connectivity)CONN COVERS LACING TERMINATION Datasheet资料下载
参数资料
| 型号： | 91293-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/4页 |
| 文件大小： | 0K |
| 描述： | CONN COVERS LACING TERMINATION |
| RoHS指令信息： | 91293-1 Statement of Compliance |
| 标准包装： | 1 |
| 系列： | AMPMODU |
| 附件类型： | 外壳线束固定 |
| 适用于相关产品： | Amplimite 0.050 系列连接器 |
408-9750
6. Place a properly prepared cable into the clamp,
with the wires protruding upward through the lacing
fixture, and with the edge of the cable jacket
approximately even with the top edge of the cable
clamp.
NOTE
i
If necessary, a pointed instrument can be used to
help remove the wires from the inside combs. Take
care to avoid damaging the insulation or pulling the
wires out of the clip in the termination cover.
NOTE
i
NOTE
7. Close the latch by hooking over the pin on the
clamp.
If the clamp is too tight or too loose, adjust the
clamp by moving the jaw using the setscrew
located in the back of the clamp block. Refer to
8. Position the cable clamp so that the cable bundle
is centrally located on the termination cover. To
position the clamp, loosen, but do not remove, the
socket head cap screws in the cable clamp bracket
and slide the clamp to the desired position. Refer to
9. After the cable is secured, untwist the wires (if
twisted) and lace the individual wires into the wire
slots. Pull each wire into the proper slot in the comb.
Continue pulling downward on each wire until the
wire is snug in the slot. When in place, the wire
should not pop out of the slot.
For ease of termination, start at one end of the
covers and work toward the opposite end.
i
15. .After the wires are correctly seated into the
termination covers, the covers can be seated onto
the connector. For cover seating procedure, refer to
Instruction Sheet 408-9820.
5. REPLACEABLE PARTS
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed should
be replaced by Tyco Electronics Corporation to ensure
quality and reliability. Order replacement parts through
your representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to 717-986-7605, or
write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
PART NUMBER DESCRIPTION
10. After all of the wires are laced, slide the lacing
fixture subassembly back under the upper tooling
assembly until it butts against the stop.
91293-1
Cover Lacing Fixture (Includes Slide
Assembly, Upper Tooling Assembly, Two 50-
position Seating Bars, Two 100-position
Seating Bars, and Lacing Fixture
Subassembly 543481-1)
NOTE
i
If using the bench stand, remove the lacing fixture
subassembly and place it into the slide of the arbor
frame assembly. Slide the lacing fixture
subassembly back until it butts against the stop.
543481-1
543494-2
Lacing Fixture Subassembly
(Includes Bench Stand And Clamp)
26-Position Seating Bar
11. Pull the arbor frame handle downward to seat
and cut the wires. The action of the wires entering
the clips on the termination covers should be felt
through the handles as a slight "snap."
543494-1
543502-2
543502-1
50-Position Seating Bar
68-Position Seating Bar
100-Position Seating Bar
12. While maintaining pressure on the arbor frame
handle, remove the cut wire ends protruding from
the lacing fixture subassembly.
6. REVISION SUMMARY
Figure 8
13. Lift the arbor frame handle to raise the upper
tooling assembly. Slide the lacing fixture
subassembly out, then open the cable clamp.
14. Carefully push upward on the cable, and
remove the covers from the lacing fixture
subassembly.
Rev D
Since the previous release of thiss document, the new
company logo has been applied.
4 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 91302-1 | TOOL CST-100 EXTRACTION |
| 91308-1 | EXT TOOL AMP INNERGY WIRE BRD |
| 91311-2 | 12 ROW HM SEATING TOOL ASSY |
| 91312-1 | 10 ROW HS3 SEATING TOOL ASSY |
| 91318-1 | 12 ROW RECPT SEAT TOOL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 912-931 | 制造商:SPC Multicomp 功能描述:CAPACITOR 100UF 16V |
| 912-935 | 功能描述:支架与垫片 Plastic Spcr .935 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 9129386 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 9-1293-TR | 制造商:KEYSTONE 功能描述:SCREW TERMINAL ON TAPE & REEL (250PCS) |
| 91294 | 制造商:Amphenol Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。