- 您现在的位置：买卖IC网 > Datasheet目录613 > 91369-2 (TE Connectivity)PRO-C DIE SL156 16 Datasheet资料下载
参数资料
| 型号： | 91369-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | PRO-C DIE SL156 16 |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | Q3099740A |
Figure 2
screw just enough to hold the dies in place. Do not
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with two
crimping sections.
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
Attached to the outside of the frame is a locator
assembly, which contains a locator, a spring retainer,
and a contact support.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame. A
nut is used on the upper die retaining screw to hold
the locator assembly in place.
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two die retaining pins.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
10. Place the nut onto the end of the long screw
and tighten the nut enough to hold the locator
assembly in place, while still allowing the locator to
slide up and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the
four die retaining pins, and slide the anvils and
crimpers out of the tool jaws.
相关PDF资料 |
PDF描述 |
|---|---|
| 91376-1 | SEATING TL RCPT HMZD 3 PR |
| 91391-2 | SDE ERGO DIE MICRO MNL |
| 913923-1 | EXTRACTON TOOL FOR 175150 |
| 91411-2 | MASS TERMINATION APPLICATOR |
| 91417-1 | TOOL KEYING (AMPMODU MTE) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 913694 | 制造商:ERNI Electronics 功能描述:R96MABCVVV3-00EE2513.0*30FEP01* 制造商:ERNI Electronics 功能描述:913694 / R 96 M ABC VVV 3-00 EE25 / DIN M |
| 913-695 | 功能描述:支架与垫片 Plastic Spcr .695 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 913696 | 制造商:ERNI Electronics 功能描述:R96MABCVVV3-00EE2517.0*207EP01* 制造商:ERNI Electronics 功能描述:913696 / R 96 M ABC VVV 3-00 EE25 / DIN M |
| 913697 | 制造商:ERNI Electronics 功能描述:R96MABCVVV3-00GA0604.0*20FE018* 制造商:ERNI Electronics 功能描述:913697 / R 96 M ABC VVV 3-00 GA06 / DIN M |
| 913-698 | 制造商:SPC Multicomp 功能描述:CAPACITOR 105C 10UF 35V |
发布紧急采购，3分钟左右您将得到回复。