- 您现在的位置：买卖IC网 > Datasheet目录613 > 91369-2 (TE Connectivity)PRO-C DIE SL156 16 Datasheet资料下载
参数资料
| 型号： | 91369-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | PRO-C DIE SL156 16 |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | Q3099740A |
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop,
as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
7. Check the contact’s crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, CRIMP HEIGHT ADJUSTMENT.
Figure 4
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher–numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower–numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
This inspection requires the use of a micrometer with
a modified anvil. Tyco Electronics does not
manuafacture or market these gages, however TE
recommends a modified micrometer (Crimp Height
Comparator RS–1019–5LP).
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
CRIMP HEIGHT ADJUSTMENT.
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
Figure 5
Ensure that the tool and dies are clean by wiping
them with a clean, soft cloth. Remove any debris with
a clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in
the crimping dies, and store in a clean, dry area.
相关PDF资料 |
PDF描述 |
|---|---|
| 91376-1 | SEATING TL RCPT HMZD 3 PR |
| 91391-2 | SDE ERGO DIE MICRO MNL |
| 913923-1 | EXTRACTON TOOL FOR 175150 |
| 91411-2 | MASS TERMINATION APPLICATOR |
| 91417-1 | TOOL KEYING (AMPMODU MTE) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 913694 | 制造商:ERNI Electronics 功能描述:R96MABCVVV3-00EE2513.0*30FEP01* 制造商:ERNI Electronics 功能描述:913694 / R 96 M ABC VVV 3-00 EE25 / DIN M |
| 913-695 | 功能描述:支架与垫片 Plastic Spcr .695 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 913696 | 制造商:ERNI Electronics 功能描述:R96MABCVVV3-00EE2517.0*207EP01* 制造商:ERNI Electronics 功能描述:913696 / R 96 M ABC VVV 3-00 EE25 / DIN M |
| 913697 | 制造商:ERNI Electronics 功能描述:R96MABCVVV3-00GA0604.0*20FE018* 制造商:ERNI Electronics 功能描述:913697 / R 96 M ABC VVV 3-00 GA06 / DIN M |
| 913-698 | 制造商:SPC Multicomp 功能描述:CAPACITOR 105C 10UF 35V |
发布紧急采购，3分钟左右您将得到回复。