- 您现在的位置：买卖IC网 > Datasheet目录613 > 91964-2 (TE Connectivity)S.D.E.PREM.DIE ASSY 22-16 PIDG Datasheet资料下载
参数资料
| 型号： | 91964-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 5/8页 |
| 文件大小： | 0K |
| 描述： | S.D.E.PREM.DIE ASSY 22-16 PIDG |
| 标准包装： | 1 |
| 系列： | * |
408-8732
Figure 6
2. Make certain that all die-retaining screws and
die components are properly secured.
3. Inspect the crimping surfaces for flattened,
chipped, worn, or cracked areas. If damage is
evident, the dies must be replaced. Refer to
Section 7, REPLACEMENT.
6.3. Gaging the Crimping Chamber
Each tool is inspected for proper die closures before
packaging. An inspection should be performed
periodically to check the tool die closures for
excessive wear.
This inspection requires the use of plug gages
conforming to the dimensions listed in Figure 7. Tyco
Electronics does not manufacture or market these
gages. Refer to 408-7424 for information concerning
plug gages and crimp-height comparators.
To gage the crimping area(s), refer to Figure 8 and
proceed as follows:
1. Clean oil or dirt from the crimping chamber and
plug gage.
2. Cycle the SDE power unit until wire barrel dies
are bottomed. Do not apply additional pressure.
NOTE
i
Rev A
The following plug gaging information for insulation
crimping chambers is provided for customers
specifically requiring this information. If plug gaging
is not required, inspect the die closures using an
alternate procedure, i.e., performing the "Insulation
Crimp Adjustment" (see Section 5) and "Visual
Inspection" (see Paragraph 6.3).
3. With wire barrel dies bottomed, inspect the
wire barrel crimping chamber using the proper
plug gage. Lift the spring-loaded locator up and
hold gage in straight alignment with the crimping
chamber. Carefully try to insert, without forcing,
the GO element. See Figure 8. The GO element
must pass completely through the crimping area.
5 of 8
相关PDF资料 |
PDF描述 |
|---|---|
| 91965-2 | S.D.E.PREM.DIE ASSY 12-10 PIDG |
| 929013 | KNOCKOUT TOOL |
| 931800-1 | ELEC PWR UNIT W/O F/TRK OR HD |
| 937317-1 | TOOL PUNCH MINI CT PISTOL GRIP |
| 947679-1 | TOOL HAND CRIMPER HE-14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91-9642-27 | 制造商:GLOBAL MEASUREMENT AND CONTROL 功能描述:WIRE PTFE A YELLOW 7/0.2MM 25M |
| 91964-P2S2 | 制造商:Nuvotem 功能描述:Transformer Toroidal 300VA 2x25V o/p |
| 91965-2 | 功能描述:冲压机与冲模 S.D.E.PREM.DIE ASSY 12-10 PIDG RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 919655 | 制造商:Weidmuller 功能描述:CONN D-SUB F 50 POS SLDR ST PNL MNT 50TERM - Bulk |
| 919655-000 | 制造商:TE Connectivity 功能描述:CBL 1CNDCTR 26AWG 0.81MM SILV PLTD CPPR LGT GRN 600VAC - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:High Performance Cable 1Conductors 26AWG 0.81mm Silver Plated Copper Light Green 600VAC |
发布紧急采购，3分钟左右您将得到回复。