- 您现在的位置：买卖IC网 > Datasheet目录613 > 91965-2 (TE Connectivity)S.D.E.PREM.DIE ASSY 12-10 PIDG Datasheet资料下载
参数资料
| 型号： | 91965-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/7页 |
| 文件大小： | 0K |
| 描述： | S.D.E.PREM.DIE ASSY 12-10 PIDG |
| 标准包装： | 1 |
| 系列： | * |
408-8733
SDE 1600
Power Unit
(ref)
Die
Retaining
Screws
Indenter
Dies
PIDG
Locator
Assembly
Anvil
Dies
5. If the wire pulls out, set the insulation
adjustment indicator to next tighter position -
Position 3.
6. Perform a crimp and repeat adjustment as
necessary until desired insulation grip is
obtained. Do not use a tighter setting than
required.
6. MAINTENANCE AND INSPECTION
Although the dies are inspected at the factory prior to
their shipment, it is recommended that a maintenance
and inspection program be performed at your facility
periodically. This is necessary to assure that continued
use of the dies will result in the same dependability
and uniform terminations for which the dies were
designed.
NOTE
Figure 3
5. .INSULATION CRIMP ADJUSTMENT
PIDG terminals and splices feature an “insulation
grip.”
i
Each tool has four insulation crimp positions. See
Figure 1.
1. Loosen insulation adjustment locking screw
(see top of tool) and turn indicator to Position 4.
2. Place terminal or splice in tool dies.
3. .Insert UNSTRIPPED wire into ONLY the
insulation barrel of terminal or splice.
4. Perform a crimp. Remove crimped terminal or
splice and check insulation grip as follows: Bend
the wire back and forth once. Terminal or splice
should retain grip on wire insulation.
Locator Wire
Barrel
We recommend an initial frequency of once a month,
however frequency may be adjusted to suit your
requirements through experience. Frequency should
be dependant on:
? Care, amount of handling, and use of the dies;
? Type and size of the product being crimped;
? Degree of operator skill;
? Presence of abnormal amounts of dirt and dust;
and
? Your own established standards.
6.1. Maintenance
1. Remove dust, moisture, and other
contaminants with a clean, soft brush, or a clean,
soft, lint-free cloth. Do NOT use any objects that
could damage the dies or tool.
2. Make sure that the proper die-retaining screws
are properly secured.
3. When the dies are not in use, store them in a
clean, dry area.
4. Store the tool with the tool handles closed to
prevent objects from becoming lodged within the
jaws.
6.2. Visual Inspection
1. Remove all lubrication and accumulated film
from the dies by immersing the dies in a suitable
commercial degreaser.
2. Make certain that all die-retaining screws and
die components are properly secured.
Rev A
Tongue
Wire Barrel
Against Locator
Figure 4
3. Inspect the crimping surfaces for flattened,
chipped, worn, or cracked areas. If damage is
evident, the dies must be replaced. Refer to
Section 7, REPLACEMENT.
3 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| 929013 | KNOCKOUT TOOL |
| 931800-1 | ELEC PWR UNIT W/O F/TRK OR HD |
| 937317-1 | TOOL PUNCH MINI CT PISTOL GRIP |
| 947679-1 | TOOL HAND CRIMPER HE-14 |
| 960-702-170-000 | TOOL HAND CRIMP 26-30AWG MICRO-D |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 919655 | 制造商:Weidmuller 功能描述:CONN D-SUB F 50 POS SLDR ST PNL MNT 50TERM - Bulk |
| 919655-000 | 制造商:TE Connectivity 功能描述:CBL 1CNDCTR 26AWG 0.81MM SILV PLTD CPPR LGT GRN 600VAC - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:High Performance Cable 1Conductors 26AWG 0.81mm Silver Plated Copper Light Green 600VAC |
| 9196550000 | 功能描述:INTERFACE CBL DSUB FEMALE W/SCRW RoHS:是 类别:连接器，互连式 >> 接线板 - 接口模块 系列:Econoline RD 产品变化通告:Product Discontinuation 07/Oct/2011 标准包装:1 系列:PLUSCON VS 制程端连接:接线座，螺钉连接 控制端连接:RJ45 插孔（8） 控制端线缆固定器:- 位置 / 电极:64 特点:- 电压 - 额定:60V 额定电流（每触点）:1A 工作温度:0°C ~ 70°C 长度:8.31"（211.00mm） 宽:3.53"（89.60mm） 线规:20-26 AWG 其它名称:VS-PP-R-8XRJ45/5-SC |
| 919656 | 功能描述:INTERFACE CBL DSUB MALE W/SCREW RoHS:是 类别:连接器，互连式 >> 接线板 - 接口模块 系列:Econoline RD 产品变化通告:Product Discontinuation 07/Oct/2011 标准包装:1 系列:PLUSCON VS 制程端连接:接线座，螺钉连接 控制端连接:RJ45 插孔（8） 控制端线缆固定器:- 位置 / 电极:64 特点:- 电压 - 额定:60V 额定电流（每触点）:1A 工作温度:0°C ~ 70°C 长度:8.31"（211.00mm） 宽:3.53"（89.60mm） 线规:20-26 AWG 其它名称:VS-PP-R-8XRJ45/5-SC |
| 9196560000 | 功能描述:RD-50JS 制造商:weidmuller 系列:* 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。