- 您现在的位置：买卖IC网 > Datasheet目录613 > 91965-2 (TE Connectivity)S.D.E.PREM.DIE ASSY 12-10 PIDG Datasheet资料下载
参数资料
| 型号： | 91965-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 5/7页 |
| 文件大小： | 0K |
| 描述： | S.D.E.PREM.DIE ASSY 12-10 PIDG |
| 标准包装： | 1 |
| 系列： | * |
408-8733
Figure 6
NOTE
i
6.3. Gaging the Crimping Chamber
Each tool is inspected for proper die closures before
packaging. An inspection should be performed
periodically to check the tool die closures for
excessive wear.
The following plug gaging information for insulation
crimping chambers is provided for customers
specifically requiring this information. If plug gaging
is not required, inspect the die closures using an
alternate procedure, i.e., performing the “Insulation
Crimp Adjustment” (see Section 5) and “Visual
Inspection” (see Paragraph 6.3).
This inspection requires the use of plug gages
conforming to the dimensions listed in Figure 7. Tyco
Electronics does not manufacture or market these
gages. for information concerning plug gages and
micrometers, refer to 408-7424.
Rev A
To gage the crimping area(s), refer to Figure 8 and
proceed as follows:
1. Clean oil or dirt from the crimping chamber and
plug gage.
2. Cycle the SDE power unit until wire barrel dies
are bottomed. Do not apply additional pressure.
3. With wire barrel dies bottomed, inspect the
wire barrel crimping chamber using the proper
plug gage. Lift the spring-loaded locator up and
hold gage in straight alignment with the crimping
chamber. Carefully try to insert, without forcing,
the GO element. See Figure 8. The GO element
must pass completely through the crimping area.
4. Try to insert the NO-GO element. The NO-GO
element may enter partially, but must not pass
completely through the crimping area.
5 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| 929013 | KNOCKOUT TOOL |
| 931800-1 | ELEC PWR UNIT W/O F/TRK OR HD |
| 937317-1 | TOOL PUNCH MINI CT PISTOL GRIP |
| 947679-1 | TOOL HAND CRIMPER HE-14 |
| 960-702-170-000 | TOOL HAND CRIMP 26-30AWG MICRO-D |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 919655 | 制造商:Weidmuller 功能描述:CONN D-SUB F 50 POS SLDR ST PNL MNT 50TERM - Bulk |
| 919655-000 | 制造商:TE Connectivity 功能描述:CBL 1CNDCTR 26AWG 0.81MM SILV PLTD CPPR LGT GRN 600VAC - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:High Performance Cable 1Conductors 26AWG 0.81mm Silver Plated Copper Light Green 600VAC |
| 9196550000 | 功能描述:INTERFACE CBL DSUB FEMALE W/SCRW RoHS:是 类别:连接器，互连式 >> 接线板 - 接口模块 系列:Econoline RD 产品变化通告:Product Discontinuation 07/Oct/2011 标准包装:1 系列:PLUSCON VS 制程端连接:接线座，螺钉连接 控制端连接:RJ45 插孔（8） 控制端线缆固定器:- 位置 / 电极:64 特点:- 电压 - 额定:60V 额定电流（每触点）:1A 工作温度:0°C ~ 70°C 长度:8.31"（211.00mm） 宽:3.53"（89.60mm） 线规:20-26 AWG 其它名称:VS-PP-R-8XRJ45/5-SC |
| 919656 | 功能描述:INTERFACE CBL DSUB MALE W/SCREW RoHS:是 类别:连接器，互连式 >> 接线板 - 接口模块 系列:Econoline RD 产品变化通告:Product Discontinuation 07/Oct/2011 标准包装:1 系列:PLUSCON VS 制程端连接:接线座，螺钉连接 控制端连接:RJ45 插孔（8） 控制端线缆固定器:- 位置 / 电极:64 特点:- 电压 - 额定:60V 额定电流（每触点）:1A 工作温度:0°C ~ 70°C 长度:8.31"（211.00mm） 宽:3.53"（89.60mm） 线规:20-26 AWG 其它名称:VS-PP-R-8XRJ45/5-SC |
| 9196560000 | 功能描述:RD-50JS 制造商:weidmuller 系列:* 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。