- 您现在的位置：买卖IC网 > PDF目录21922 > A1183LUA-T (Allegro Microsystems Inc)IC SWITCH HALL EFFECT UNI 3-SIP PDF资料下载
参数资料
| 型号： | A1183LUA-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 12/16页 |
| 文件大小： | 543K |
| 描述： | IC SWITCH HALL EFFECT UNI 3-SIP |
| 产品培训模块： | Current Sensor |
| 标准包装： | 500 |
| 传感范围： | 60G ~ 200G 跳闸 - 可编程，固定释放 |
| 类型： | 单极开关 |
| 电源电压： | 3.5 V ~ 24 V |
| 电流 - 电源： | 6.9mA |
| 输出类型： | 数字，开路集电极 |
| 特点： | 可编程 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 3-SIP |
| 供应商设备封装： | 3-SIP |
| 包装： | 散装 |
Sensitive Two-Wire Field-Programmable
Chopper-Stabilized Unipolar Hall Effect Switches
A1180, A1181,
A1182, and A1183
11
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
PROGRAMMING PROTOCOL CHARACTERISTICS, over operating temperature range, unless otherwise noted
Characteristic
Symbol
Test Conditions
Min. Typ. Max. Units
Programming Voltage
1
V
PL
Minimum voltage range during programming
4.5 5.0 5.5 V
V
PM
11.5 12.5 13.5 V
V
PH
25.0 26.0 27.0 V
Programming Current
2
I
PP
t
r
= 11 約; 5 V ?26 V; C
BYP
= 0.1 糉
- 190 -
mA
Pulse Width
t
d(0)
OFF time between programming bits
20
-
-
約
t
d(1)
Pulse duration for enable and addressing
sequences
20
-
-
約
t
d(P)
Pulse duration for fuse blowing
100 300 -
約
Pulse Rise Time
t
r
V
PL
to V
PM
;
V
PL
to V
PH
5
-
20 約
Pulse Fall Time
t
f
V
PM
to V
PL
; V
PH
to V
PL
5
- 100 約
1
Programming voltages are measured at the VCC pin.
2
A bypass capacitor with a minimum capacitance of 0.1 糉 must be connected from VCC to the GND pin of the A118x device in order to
provide the current necessary to blow the fuse.
V
PH
V+
t
V
PM
V
PL
0
T
d(1)
T
d(0)
T
d(P)
Figure 4. Pulse amplitudes and durations
Additional information on device programming and program-
ming products is available on www. allegromicro.com. Program-
ming hardware is available for purchase, and programming
software is available free of charge.
Programming Protocol
The operate switchpoint, B
OP
, can be eld-programmed. To do
so, a coded series of voltage pulses through the VCC pin is used
to set bit elds in onboard registers. The effect on the device
output can be monitored, and the registers can be cleared and
set repeatedly until the required B
OP
is achieved. To make the
setting permanent, bit eld-level solid state fuses are blown, and
nally, a device-level fuse is blown, blocking any further cod-
ing. It is not necessary to program the release switchpoint, B
RP
,
because the difference between B
OP
and B
RP
, referred to as the
hysteresis, B
HYS
, is xed.
The range of values between B
OP(min)
and B
OP(max)
is scaled to
31 increments. The actual change in magnetic ux (G) repre-
sented by each increment is indicated by B
RES
(see the Operating
Characteristics table; however, testing is the only method for
verifying the resulting B
OP
). For programming, the 31 incre-
ments are individually identi ed using 5 data bits, which are
physically represented by 5 bit elds in the onboard registers.
By setting these bit elds, the corresponding calibration value is
programmed into the device.
Three voltage levels are used in programming the device: a low
voltage, V
PL
, a minimum required to sustain register settings; a
mid-level voltage, V
PM
, used to increment the address counter
in the device; and a high voltage, V
PH
, used to separate sets of
V
PM
pulses (when short in duration) and to blow fuses (when
long in duration). A fourth voltage level, essentially 0 V, is used
to clear the registers between pulse sequences. The pulse values
are shown in the Programming Protocol Characteristics table and
in gure 4.
Code Programming. Each bit eld must be individually set. To
do so, a pulse sequence must be transmitted for each bit eld that
is being set to 1. If more than one bit eld is being set to 1, all
pulse sequences must be sent, one after the other, without allow-
ing V
CC
to fall to zero (which clears the registers).
The same pulse sequence is used to provisionally set bit elds as
is used to permanently set bit eld-level fuses. The only differ-
ence is that when provisionally setting bit elds, no fuse-blowing
pulse is sent at the end of the pulse sequence.
相关PDF资料 |
PDF描述 |
|---|---|
| 6283-C-36 | PLUG DBL BANA W/SAFE SHROUD 36" |
| 6483-48-2 | ALLIG 5 WAY-R/A BANANA PLUG RED |
| A1183LUA | IC SWITCH HALL EFFECT UNI 3-SIP |
| 6483-48-0 | ALLIG 5 WAY-R/A BANANA PLUG BLK |
| 6485-48-0 | BED OF NAILS TO R/A BANANA BLACK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A1184 | 制造商:Quick 功能描述:SOJ 18 X 8 NOZZLE FOR QUICK957/957D |
| A118-4 | 制造商:APEM 功能描述: |
| A1184_06 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Standard Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1184_11 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A1184 device is a standard, two-wire, unipolar, Hall effect switch. |
| A1184B | 制造商:HAKKO Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。