- 您现在的位置：买卖IC网 > PDF目录18803 > A1190LUA-T (Allegro Microsystems Inc)IC SW HALL EFFECT CHOPPER 3SIP PDF资料下载
参数资料
| 型号： | A1190LUA-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 11/18页 |
| 文件大小： | 383K |
| 描述： | IC SW HALL EFFECT CHOPPER 3SIP |
| 特色产品： | A119x Switches |
| 标准包装： | 4,000 |
| 类型： | 单极开关 |
| 电源电压： | 3 V ~ 24 V |
| 电流 - 电源： | 5mA |
| 输出类型： | 数字 |
| 特点： | 可编程 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 3-SSIP |
| 供应商设备封装： | 3-SIP |
| 包装： | 散装 |
| 其它名称： | 620-1406 |
Programmable, Chopper-Stabilized,
Two Wire Hall-Effect Switches
A1190, A1192,
and A1193
11
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Try Mode In Try mode, bit field addressing is accomplished by
applying a series of V
PM
pulses to the VCC pin of the device, as
shown in figure 6. Each pulse increases the bit field value for the
selected parameter, increasing by one on the falling edge of each
additional V
PM
pulse. When addressing the bit field in Try mode,
the quantity of V
PM
pulses is represented by a decimal number
called the code. Addressing activates the corresponding fuse
locations in the given bit field by increasing the binary value of
an internal DAC, up to the maximum possible code. As the value
of the bit field code increases, the value of the programmable
parameter changes. Measurements can be taken after each V
PM
pulse to determine if the required result for the programmable
parameter has been reached. Cycling the supply voltage resets
all the locations in the bit field that have un-blown fuses to their
initial states.
When setting the B
OP
Trim parameter, as an aid to programming,
values can be traversed from low to high, or from high to low. To
accommodate this direction selection, the value of the bit field
(and code) defaults to the value 1, on the falling edge of the final
register selection V
PH
pulse (see figure 5). A complete example is
provided in figure 11.
Blow Mode After the required code is determined for a given
parameter, its value can be set permanently by blowing individual
fuses in the appropriate register bit field. Blowing is accom-
plished by selecting the register, then the Blow mode selection
key, followed by the appropriate bit field address, and ending
the sequence with the Blow pulse. The Blow mode selection key
is a sequence of nine V
PM
pulses followed by one V
PH
pulse. A
complete example is provided in figure 12.
The Blow pulse consists of a V
PH
pulse of sufficient duration,
t
BLOW
, to permanently set an addressed bit by blowing a fuse
internal to the device. Due to power requirements, the fuse for
each bit in the bit field must be blown individually. The A119x
family built-in circuitry allows only one fuse at a time to be
blown. During Blow mode, the bit field can be considered a one-
hot shift register. Table 3 relates the quantity of V
PM
pulses to
the binary and decimal values for Blow mode bit field address-
ing. It should be noted that the simple relationship between the
quantity of V
PM
pulses and the corresponding code is:
2
n
= Code,
where n is the quantity of V
PM
pulses. The bit field has an initial
state of decimal code 0 (binary 000000).
Figure 6. Try mode bit field addressing pulses
Figure 7. Example of code 5 broken into its binary components
0
V
PH
V
PM
V
PL
Table 3. Blow Mode Bit Field Addressing
Quantity of
V
PM
Pulses
Binary Register
Setting
Equivalent Code
1
000001
1
2
000010
2
3
000100
4
4
001000
8
5
010000
16
6
100000
32
(Decimal Equivalent)
Code 5
Bit Field Selection
Address Code Format
Code in Binary
Fuse Blowing
Target Bits
Fuse Blowing
Address Code Format
(Binary)
1 0 1
Bit 2
Bit 0
Code 4 Code 1
(Decimal Equivalents)
0
Key
V
PH
V
PM
V
PL
Figure 5. Register selection pulse sequence
相关PDF资料 |
PDF描述 |
|---|---|
| R9G23412CSOO | RECTIFIER FAST REC 3400V 1200A |
| A1192LUA-T | IC SW HALL EFFECT CHOPPER 3SIP |
| R9G02612XX | RECTIFIER 2600V 1200A |
| P143-125.0M | OSC 125.0000MHZ 3.3V LVPECL SMD |
| P223-100.0M | OSC 100.0000MHZ 3.3V LVPECL SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A1190LUBTN-T | 功能描述:2-WIRE FIELD PROGRAMMABLE SWITCH 制造商:allegro microsystems, llc 系列:* 零件状态:新产品 标准包装:1 |
| A1191 | 制造商:Quick 功能描述:SIP 25L 25mm Nozzle for 21-13205 and 21-13210 制造商:QUICK 功能描述:SIP 25L NOZZLE FOR QUICK957/957D |
| A-1191-1 | 功能描述:固态继电器-工业安装 DC SOLENOID RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| A1192 | 制造商:Quick 功能描述:SIP 50LNOZZLE FOR QUICK957/957D |
| A11927-01 | 制造商:LAIRD TECHNOLOGIES - THERMAL MATERIALS 功能描述:TGON 810 SA 18" X 23" 制造商:Laird Technologies Inc 功能描述:TGON 810 SA 18" X 23" 制造商:Laird Technologies Inc 功能描述:TGON 810,SA / 18 X 23 |
发布紧急采购，3分钟左右您将得到回复。