- 您现在的位置：买卖IC网 > PDF目录18803 > A1190LUA-T (Allegro Microsystems Inc)IC SW HALL EFFECT CHOPPER 3SIP PDF资料下载
参数资料
| 型号： | A1190LUA-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 9/18页 |
| 文件大小： | 383K |
| 描述： | IC SW HALL EFFECT CHOPPER 3SIP |
| 特色产品： | A119x Switches |
| 标准包装： | 4,000 |
| 类型： | 单极开关 |
| 电源电压： | 3 V ~ 24 V |
| 电流 - 电源： | 5mA |
| 输出类型： | 数字 |
| 特点： | 可编程 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 3-SSIP |
| 供应商设备封装： | 3-SIP |
| 包装： | 散装 |
| 其它名称： | 620-1406 |
Programming Guidelines
Overview
Programming is accomplished by sending a series of input volt-
age pulses serially through the VCC (supply) pin of the device.
A unique combination of different voltage level pulses controls
the internal programming logic of the device to select a desired
programmable parameter and change its value. There are three
voltage levels that must be taken into account when program-
ming. These levels are referred to as high (V
PH
), mid (V
PM
), and
low (V
PL
) (see figure 1 and table 1).
The A119x family features two programmable modes, Try mode
and Blow mode.
" In Try mode, programmable parameter values are set and mea-
sured. A parameter value is stored temporarily, and reset after
cycling the supply voltage.
" In Blow mode, the value of a programmable parameter may
be permanently set by blowing solid-state fuses internal to the
device. Device locking is also accomplished in this mode.
The programming sequence is designed to help prevent the
device from being programmed accidentally; for example, as a
result of noise on the supply line. Although any programmable
variable power supply can be used to generate the pulse wave-
forms, Allegro highly recommends using the Allegro Sensor IC
Evaluation Kit, available on the Allegro website On-line Store.
The manual for that kit is available for download free of charge,
and provides additional information on programming these
devices.
Definition of Terms
Register. The section of the programming logic that controls the
choice of programmable modes and parameters.
Bit Field. The internal fuses unique to each register, represented
as a binary number. Changing the bit field selection in a particu-
lar register causes its programmable parameter to change, based
on the internal programming logic.
Key. A series of V
PM
voltage pulses used to select a register or mode.
Table 1. Programming Pulse Requirements, Protocol at T
A
= 25癈 (refer also to figure 4)
Characteristic Symbol
Notes
Min. Typ. Max. Unit
Programming Voltage
V
PL
Measured at the VCC pin.
4.5 5 5.5 V
V
PM
12.5 14 V
V
PH
21 27 V
Programming Current I
PP
t
Pr
= 11 約, V
CC
= 5 ?26 V, C
BLOW
= 0.1 糉 (min). Minimum supply current
required to ensure proper fuse blowing. C
BLOW
must be connected between the
VCC and GND pins during programming to provide the current necessary for fuse
blowing.
175 mA
Pulse Width
t
LOW
Duration at V
PL
separating pulses at V
PM
or V
PH
.
20 約
t
ACTIVE
Duration of pulses at V
PM
or V
PH
for key/code selection.
20 約
t
BLOW
Duration of pulse at V
PH
for fuse blowing.
90 100 約
Pulse Rise Time
t
Pr
V
PL
to V
PM
, or V
PL
to V
PH
.
5 100 約
Pulse Fall Time
t
Pf
V
PH
to V
PL
, or V
PM
to V
PL
.
5 100 約
Blow Pulse Slew Rate SR
BLOW
375 mV/ 約
0
(Supply
cycled)
Programming
pulses
Blow
pulse
t
ACTIVE
t
LOW
t
LOW
t
BLOW
t
Pr
t
Pf
V
PH
V
PM
V
PL
Figure 4. Programming pulse definition (see table 1)
Programmable, Chopper-Stabilized,
Two Wire Hall-Effect Switches
A1190, A1192,
and A1193
9
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相关PDF资料 |
PDF描述 |
|---|---|
| R9G23412CSOO | RECTIFIER FAST REC 3400V 1200A |
| A1192LUA-T | IC SW HALL EFFECT CHOPPER 3SIP |
| R9G02612XX | RECTIFIER 2600V 1200A |
| P143-125.0M | OSC 125.0000MHZ 3.3V LVPECL SMD |
| P223-100.0M | OSC 100.0000MHZ 3.3V LVPECL SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A1190LUBTN-T | 功能描述:2-WIRE FIELD PROGRAMMABLE SWITCH 制造商:allegro microsystems, llc 系列:* 零件状态:新产品 标准包装:1 |
| A1191 | 制造商:Quick 功能描述:SIP 25L 25mm Nozzle for 21-13205 and 21-13210 制造商:QUICK 功能描述:SIP 25L NOZZLE FOR QUICK957/957D |
| A-1191-1 | 功能描述:固态继电器-工业安装 DC SOLENOID RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| A1192 | 制造商:Quick 功能描述:SIP 50LNOZZLE FOR QUICK957/957D |
| A11927-01 | 制造商:LAIRD TECHNOLOGIES - THERMAL MATERIALS 功能描述:TGON 810 SA 18" X 23" 制造商:Laird Technologies Inc 功能描述:TGON 810 SA 18" X 23" 制造商:Laird Technologies Inc 功能描述:TGON 810,SA / 18 X 23 |
发布紧急采购，3分钟左右您将得到回复。