- 您现在的位置：买卖IC网 > PDF目录364573 > A29L040SERIES 512K X 8 Bit CMOS 3.0 Volt-only. Uniform Sector Flash Memory PDF资料下载
参数资料
| 型号： | A29L040SERIES |
| 英文描述： | 512K X 8 Bit CMOS 3.0 Volt-only. Uniform Sector Flash Memory |
| 中文描述： | 为512k × 8位CMOS 3.0伏特只。统一部门闪存 |
| 文件页数： | 13/30页 |
| 文件大小： | 285K |
| 代理商： | A29L040SERIES |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
I/O
3
: Sector Erase Timer
A29L040 Series
PRELIMINARY (December, 2002, Version 0.0)
13
AMIC Technology, Corp.
After writing a sector erase command sequence, the
system may read I/O
3
to determine whether or not an
erase operation has begun. (The sector erase timer does
not apply to the chip erase command.) If additional
sectors are selected for erasure, the entire time-out also
applies after each additional sector erase command.
When the time-out is complete, I/O
3
switches from "0" to
"1." The system may ignore I/O
3
if the system can
guarantee that the time between additional sector erase
commands will always be less than 50
μ
s. See also the
"Sector Erase Command Sequence" section.
After the sector erase command sequence is written, the
system should read the status on I/O
7
(
Data
Polling) or
I/O
6
(Toggle Bit 1) to ensure the device has accepted the
command sequence, and then read I/O
3
. If I/O
3
is "1", the
internally controlled erase cycle has begun; all further
commands (other than Erase Suspend) are ignored until
the erase operation is complete. If I/O
3
is "0", the device
will accept additional sector erase commands. To ensure
the command has been accepted, the system software
should check the status of I/O
3
prior to and following each
subsequent sector erase command. If I/O
3
is high on the
second status check, the last command might not have
been accepted. Table 5 shows the outputs for I/O
3
.
START
Read I/O
7
-I/O
0
Toggle Bit
= Toggle
Program/Erase
Operation Not
Commplete, Write
Reset Command
Yes
Notes :
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as I/O
5
changes to "1". See text.
No
Read I/O
7
- I/O
0
Twice
I/O
5
= 1
Toggle Bit
= Toggle
Yes
Yes
Program/Erase
Operation
Commplete
No
No
Read I/O
7
-I/O
0
(Notes 1,2)
Figure 4. Toggle Bit Algorithm
(Note 1)
相关PDF资料 |
PDF描述 |
|---|---|
| A29L160SERIES | 2M X 8 Bit / 1M X 16 Bit CMOS 3.0 Volt-only. Boot Sector Flash Memory |
| A29L400SERIES | 512K X 8 Bit / 256K X 16 Bit CMOS 3.0 Volt-only. Boot Sector Flash Memory |
| A29L800SERIES | 1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only. Boot Sector Flash Memory |
| A31-1 | 10 TO 2000 MHz CECASCADABLE AMPLIFIER |
| A3134*LT | BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMPERATURE OPERATION |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A29L040V | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Uniform Sector Flash Memory |
| A29L040V-55F | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Uniform Sector Flash Memory |
| A29L040V-55UF | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Uniform Sector Flash Memory |
| A29L040V-70 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Uniform Sector Flash Memory |
| A29L040V-70F | 制造商:AMIC Technology 功能描述:MEMORY FLASH NOR 3V 4M 32TSOP |
发布紧急采购，3分钟左右您将得到回复。