- 您现在的位置：买卖IC网 > PDF目录364573 > A29L160SERIES 2M X 8 Bit / 1M X 16 Bit CMOS 3.0 Volt-only. Boot Sector Flash Memory PDF资料下载
参数资料
| 型号： | A29L160SERIES |
| 英文描述： | 2M X 8 Bit / 1M X 16 Bit CMOS 3.0 Volt-only. Boot Sector Flash Memory |
| 中文描述： | 2米x 8位/ 1米× 16位CMOS 3.0伏特只。引导扇区闪存 |
| 文件页数： | 17/45页 |
| 文件大小： | 433K |
| 代理商： | A29L160SERIES |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
A29L160 Series
PRELIMINARY (July, 2002, Version 0.0)
16
AMIC Technology, Inc.
Command Definitions
Writing specific address and data commands or sequences
into the command register initiates device operations. The
Command Definitions table defines the valid register
command sequences. Writing incorrect address and data
values or writing them in the improper sequence resets the
device to reading array data.
All addresses are latched on the falling edge of
WE
or
CE
,
whichever happens later. All data is latched on the rising edge
of
WE
or
CE
, whichever happens first. Refer to the
appropriate timing diagrams in the "AC Characteristics"
section.
Reading Array Data
The device is automatically set to reading array data after
device power-up. No commands are required to retrieve data.
The device is also ready to read array data after completing
an Embedded Program or Embedded Erase algorithm. After
the device accepts an Erase Suspend command, the device
enters the Erase Suspend mode. The system can read array
data using the standard read timings, except that if it reads at
an address within erase-suspended sectors, the device
outputs status data. After completing a programming
operation in the Erase Suspend mode, the system may once
again read array data with the same exception. See "Erase
Suspend/Erase Resume Commands" for more information on
this mode.
The system must issue the reset command to re-enable the
device for reading array data if I/O
5
goes high, or while in the
autoselect mode. See the "Reset Command" section, next.
See also "Requirements for Reading Array Data" in the
"Device Bus Operations" section for more information. The
Read Operations table provides the read parameters, and
Read Operation Timings diagram shows the timing diagram.
Reset Command
Writing the reset command to the device resets the device to
reading array data. Address bits are don't care for this
command. The reset command may be written between the
sequence cycles in an erase command sequence before
erasing begins. This resets the device to reading array data.
Once erasure begins, however, the device ignores reset
commands until the operation is complete.
The reset command may be written between the sequence
cycles in a program command sequence before programming
begins. This resets the device to reading array data (also
applies to programming in Erase Suspend mode). Once
programming begins, however, the device ignores reset
commands until the operation is complete.
The reset command may be written between the sequence
cycles in an autoselect command sequence. Once in the
autoselect mode, the reset command must be written to
return to reading array data (also applies to autoselect during
Erase Suspend).
If I/O
5
goes high during a program or erase operation, writing
the reset command returns the device to reading array data
(also applies during Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host system to
access the manufacturer and devices codes, and determine
whether or not a sector is protected. The Command Definitions
table shows the address and data requirements. This method
is an alternative to that shown in the Autoselect Codes (High
Voltage Method) table, which is intended for PROM
programmers and requires V
ID
on address bit A9.
The autoselect command sequence is initiated by writing two
unlock cycles, followed by the autoselect command. The
device then enters the autoselect mode, and the system may
read at any address any number of times, without initiating
another command sequence.
A read cycle at address XX00h retrieves the manufacturer
code and another read cycle at XX11h retrieves the
continuation code. A read cycle at address XX01h returns the
device code. A read cycle containing a sector address (SA)
and the address 02h in returns 01h if that sector is protected,
or 00h if it is unprotected. Refer to the Sector Address tables
for valid sector addresses.
The system must write the reset command to exit the
autoselect mode and return to reading array data.
Word/Byte Program Command Sequence
The system may program the device by word or byte,
depending on the state of the
BYTE
pin. Programming is a
four-bus-cycle operation. The program command sequence is
initiated by writing two unlock write cycles, followed by the
program set-up command. The program address and data are
written next, which in turn initiate the Embedded Program
algorithm. The system is not required to provide further
controls or timings. The device automatically provides
internally
generated
program
programmed cell margin. Table 9 shows the address and data
requirements for the byte program command sequence.
When the Embedded Program algorithm is complete, the
device then returns to reading array data and addresses are
longer latched. The system can determine the status of the
program operation by using I/O
7
, I/O
6
, or RY/
BY
. See “White
Operation Status” for information on these status bits.
Any commands written to the device during the Embedded
Program Algorithm are ignored. Note that a hardware reset
immediately terminates the programming operation. The Byte
Program command sequence should be reinitiated once the
device has reset to reading array data, to ensure data integrity.
Programming is allowed in any sequence and across sector
boundaries. A bit cannot be programmed from a “0” back to a
“1”. Attempting to do so may halt the operation and set I/O5 to
“1”, or cause the
Data
Polling algorithm to indicate the
operation was successful. However, a succeeding read will
show that the data is still “0”. Only erase operations can
convert a “0” to a “1”.
pulses
and
verify
the
相关PDF资料 |
PDF描述 |
|---|---|
| A29L400SERIES | 512K X 8 Bit / 256K X 16 Bit CMOS 3.0 Volt-only. Boot Sector Flash Memory |
| A29L800SERIES | 1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only. Boot Sector Flash Memory |
| A31-1 | 10 TO 2000 MHz CECASCADABLE AMPLIFIER |
| A3134*LT | BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMPERATURE OPERATION |
| A3134*UA | BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMPERATURE OPERATION |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A29L160TG-120 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:2M X 8 Bit / 1M X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L160TG-70 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:2M X 8 Bit / 1M X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L160TG-90 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:2M X 8 Bit / 1M X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L160TM-120 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:2M X 8 Bit / 1M X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L160TM-70 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:2M X 8 Bit / 1M X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
发布紧急采购，3分钟左右您将得到回复。