- 您现在的位置：买卖IC网 > Datasheet目录306 > A3940KLPTR-T (Allegro Microsystems Inc)IC CTLR MOSFET FULL 28-TSSOP Datasheet资料下载
参数资料
| 型号： | A3940KLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 9/13页 |
| 文件大小： | 0K |
| 描述： | IC CTLR MOSFET FULL 28-TSSOP |
| 标准包装： | 1 |
| 配置： | 半桥 |
| 输入类型： | 非反相 |
| 延迟时间： | 225ns |
| 电流 - 峰： | 700mA |
| 配置数： | 1 |
| 输出数： | 4 |
| 电源电压： | 7 V ~ 40 V |
| 工作温度： | -40°C ~ 135°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 标准包装 |
| 其它名称： | 620-1293-6 |
3940
FULL-BRIDGE POWER
MOSFET CONTROLLER
Terminal Descriptions
CA/CB. High-side connection for bootstrap capacitor, positive
supply for high-side gate drive. The bootstrap capacitor is
charged to V REG13 – 1.5 V when the output Sx terminal is low.
When the output swings high, the voltage on this terminal rises
with the output to provide the boosted gate voltage needed for n-
channel power MOSFETs.
RESET. Control input to put device into minimum power
consumption mode and to clear latched faults. Logic “1”
enables the device; logic “0” triggers the sleep mode. Internally
pulled down via 50 k ? resistor.
ENABLE. Logic “1” enables direct control of the output
drivers via the PHASE input, as in PWM controls, and ignores
the MODE and SR inputs. Internally pulled down via 50 k ?
resistor.
MODE. Logic input to set the current decay mode. Logic “1”
(slow-decay mode) switches off the high-side MOSFET in
response to a PWM “off” command. Logic “0” (fast-decay
mode) switches off both the high-side and low-side MOSFETs.
Internally pulled down via 50 k ? resistor.
PHASE. Motor direction control. When logic “1”, enables
gate drive outputs GHA and GLB allowing current flow from
SA to SB. When logic “0”, enables GHB and GLA allowing
current flow from SB to SA. Internally pulled down via 50 k ?
resistor.
SR. When logic “1”, enables synchronous rectification; logic
“0” disables the synchronous rectification. Internally pulled
down via 50 k ? resistor.
FAULT. Open drain, diagnostic logic output signal. When
logic “1”, indicates that one or more fault conditions have
occurred. Use an external pullup resistor to VREG5 or to digital
controller. Internally causes a coast when asserted. See also
Functional Description, next page.
IDEAD. Analog current set by resistor (12 k ? <R DEAD <500 k ? )
to ground. In conjunction with LONG, determines dead time
between GHx and GLx transitions of same phase. V IDEAD = 2 V.
LONG. When logic “1”, selects long dead time between GHx
and GLx transitions of same phase. When logic “0”, selects
short dead times. Internally pulled down via 50 k ? resistor.
GHA/GHB. High-side gate-drive outputs for n-channel
MOSFET drivers. External series gate resistors can control slew
rate seen at the power driver gate.
GLA/GLB. Low-side gate drive outputs for external, n-channel
MOSFET drivers. External series gate resistors can control slew
rate seen at the power driver gate.
GND. Common ground and dc supply returns. Exposed
thermal pad of LP package is NOT internally connected to
GND.
LSS. Low-side gate drivers’ return. Connects to the common
sources in the low-side of the power MOSFET bridge. It is the
reference connection for the short-to-battery monitor.
OVSET. A positive, dc level that controls the VBB overvoltage
trip point. Usually, provided from precision resistor divider
network between V REG5 and GND. If connected directly to
V REG5 , sets unspecified but high overvoltage trip point, effec-
tively eliminating the overvoltage protection.
SA/SB. Directly connected to the motor terminals, these
terminals sense the voltages switched across the load and are
connected to the negative side of the bootstrap capacitors. Also,
are the negative supply connection for the floating, high-side
drivers.
VBB. Positive supply voltage. Usually connected to the motor
voltage supply. If V BB is above a specified level or below a
specified level, a fault will be asserted.
VDRAIN. Kelvin connection for drain-to-source voltage (short-
to-ground) monitor and is connected to high-side drains of the
MOSFET bridge. Also used to detect “open drain”.
VDSTH. A positive, dc level that sets the short-to-ground and
short-to-battery monitor threshold voltage. If the drain-source
voltage exceeds this level (after the dead time) during an “on”
state, a fault will be asserted.
CP1 [CP2]. Charge pump capacitor negative [positive] side. If
not using the charge pump, leave both terminals open.
VCP. Charge pump output for VREG13 input. If not using the
charge pump, connect this terminal to VBB.
VIN. Positive supply voltage for the V REG13 linear regulator.
Usually connected to VCP, the charge-pump output gate drive.
If not using the charge pump, connect VIN to VBB or other dc
supply greater than 11 V.
VREG13. High-side, gate-driver supply. If V REG13 falls below
a specified level, a fault will be asserted.
VREG5. Regulated 5 V output for internal logic.
8
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
相关PDF资料 |
PDF描述 |
|---|---|
| A3941KLPTR-T | IC MOSFET FULL BRDG AUTO 28TSSOP |
| A3942KLGTR-T | IC GATE DVR QUAD HISIDE 38-TSSOP |
| A3944KLPTR-T | IC PREDRIVER MOSFET 6CH TSSOP |
| A3985SLDTR-T | IC MOSFET DRVR PROG DUAL 38TSSOP |
| A4933KJPTR-T | IC PREDRIVER MOSFET 3PH 48LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3940KLW | 功能描述:IC CTRLR MOSFET FULL 28-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| A3940KLW-T | 功能描述:IC MOSFET CONTROLLER 28-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| A3940KLWTR | 功能描述:IC CTRLR MOSFET FULL 28-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| A3940KLWTR-T | 功能描述:IC CTRLR MOSFET FULL 28-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| A3941 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Automotive Full Bridge MOSFET Driver |
发布紧急采购，3分钟左右您将得到回复。