- 您现在的位置：买卖IC网 > PDF目录1773 > A3983SLP-T (Allegro Microsystems Inc)IC MICRO STEPPING DRIVER 24-TSSO PDF资料下载
参数资料
| 型号： | A3983SLP-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 6/13页 |
| 文件大小： | 0K |
| 描述： | IC MICRO STEPPING DRIVER 24-TSSO |
| 标准包装： | 62 |
| 应用： | 步进电机驱动器 |
| 输出数： | 1 |
| 电流 - 输出： | ±2A |
| 电压 - 负载： | 8 V ~ 35 V |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 24-TSSOP 裸露焊盘 |
| 包装： | 管件 |
| 其它名称： | 620-1083 |
A3983
DMOS Microstepping Driver with Translator
pin is tied to an external voltage > 3 V, then t OFF defaults to
30 μ s. The ROSC pin can be safely connected to the VDD
pin for this purpose. The value of t OFF ( μ s) is approximately
t OFF ≈ R OSC ? 825
Blanking. This function blanks the output of the current
sense comparators when the outputs are switched by the
internal current control circuitry. The comparator outputs are
blanked to prevent false overcurrent detection due to reverse
recovery currents of the clamp diodes, and switching tran-
sients related to the capacitance of the load. The blank time,
t BLANK ( μ s), is approximately
t BLANK ≈ 1 μ s
Charge Pump (CP1 and CP2). The charge pump is
used to generate a gate supply greater than that of VBB
for driving the source-side DMOS gates. A 0.1 μ F ceramic
capacitor, should be connected between CP1 and CP2. In
addition, a 0.1 μ F ceramic capacitor is required between
VCP and VBB, to act as a reservoir for operating the
high-side DMOS gates.
VREG (VREG) . This internally-generated voltage is used
to operate the sink-side DMOS outputs. The VREG pin must
be decoupled with a 0.22 μ F ceramic capacitor to ground.
VREG is internally monitored. In the case of a fault condi-
tion, the DMOS outputs of the A3983 are disabled.
Enable Input (ENABLE) . This input turns on or off all of
the DMOS outputs. When set to a logic high, the outputs are
disabled. When set to a logic low, the internal control enables
the outputs as required. The translator inputs STEP, DIR,
MS1, and MS2, as well as the internal sequencing logic, all
remain active, independent of the ENABLE input state.
Shutdown. In the event of a fault, overtemperature
(excess T J ) or an undervoltage (on VCP), the DMOS out-
puts of the A3983 are disabled until the fault condition is
removed. At power-on, the UVLO (undervoltage lockout)
circuit disables the DMOS outputs and resets the translator to
the Home state.
Sleep Mode (SLEEP). To minimize power consumption
when the motor is not in use, this input disables much of the
internal circuitry including the output DMOS FETs, current
regulator, and charge pump. A logic low on the SLEEP pin
puts the A3983 into Sleep mode. A logic high allows normal
operation, as well as start-up (at which time the A3983 drives
the motor to the Home microstep position). When emerging
from Sleep mode, in order to allow the charge pump to stabi-
lize, provide a delay of 1 ms before issuing a Step command.
Mixed Decay Operation. The bridge can operate in
Mixed Decay mode, depending on the step sequence, as
shown in figures 3 thru 5. As the trip point is reached, the
A3983 initially goes into a fast decay mode for 31.25% of
the off-time. t OFF . After that, it switches to Slow Decay mode
for the remainder of t OFF .
Synchronous Rectification . When a PWM-off cycle
is triggered by an internal fixed–off-time cycle, load current
recirculates according to the decay mode selected by the
control logic. This synchronous rectification feature turns on
the appropriate FETs during current decay, and effectively
shorts out the body diodes with the low DMOS R DS(ON) . This
reduces power dissipation significantly, and can eliminate
the need for external Schottky diodes in many applications.
Turning off synchronous rectification prevents the reversal of
the load current when a zero-current level is detected.
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
6
相关PDF资料 |
PDF描述 |
|---|---|
| A3984SLP-T | IC MICRO STEPPING DRIVER 24-TSSO |
| A3986SLDTR-T | IC DRIVER MICROSTEPPING 38-TSSOP |
| A3987SLPTR-T | IC DRIVER MICROSTEPPING 24-TSSOP |
| A3988SJP-T | IC MOTOR DVR PWM FULL BRG 48LQFP |
| A3989SEVTR-T | IC STEPPER/MOTOR DRIVER 36-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3983SLP-T | 制造商:Allegro MicroSystems LLC 功能描述:Motor Driver IC |
| A3983SLPTR | 功能描述:IC DRIVER MICROSTEPPING 24-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3983SLPTR-T | 功能描述:IC DRIVER MICROSTEPPING 24-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:步进电机驱动器，1-2 相，2 相 评估套件:- 输出数:1 电流 - 输出:800mA 电压 - 负载:10 V ~ 28 V 电源电压:4.75 V ~ 5.25 V 工作温度:-20°C ~ 90°C 安装类型:表面贴装 封装/外壳:28-SOP + 2 翼片裸露焊盘 供应商设备封装:28-HSOPHC（15.2x7.9） 包装:剪切带 (CT) 其它名称:869-1268-1 |
| A3984 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Microstepping Driver with Translator |
| A3984_08 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A3984 is a complete microstepping motor driver with built-in translator for easy operation. |
发布紧急采购，3分钟左右您将得到回复。