- 您现在的位置：买卖IC网 > PDF目录1773 > A4984SLPTR-T (Allegro Microsystems Inc)IC STEPPER MOTOR DRIVER 24TSSOP PDF资料下载
参数资料
| 型号： | A4984SLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 7/22页 |
| 文件大小： | 0K |
| 描述： | IC STEPPER MOTOR DRIVER 24TSSOP |
| 特色产品： | A498x Motor Driver Family |
| 标准包装： | 1 |
| 应用： | 步进电机驱动器 |
| 评估套件： | 可供 |
| 输出数： | 1 |
| 电流 - 输出： | ±2A |
| 电压 - 负载： | 8 V ~ 35 V |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 24-TSSOP 裸露焊盘 |
| 包装： | 标准包装 |
| 其它名称： | 620-1341-6 |
A4984
DMOS Microstepping Driver with Translator
And Overcurrent Protection
Functional Description
Device Operation. The A4984 is a complete microstep-
ping motor driver with a built-in translator for easy operation
with minimal control lines. It is designed to operate bipolar
stepper motors in full-, half-, quarter-, and eighth-step modes.
The currents in each of the two output full-bridges and all of the
N-channel DMOS FETs are regulated with fixed off-time PWM
(pulse width modulated) control circuitry. At each step, the current
for each full-bridge is set by the value of its external current-sense
resistor (R S1 and R S2 ), a reference voltage (V REF ), and the output
voltage of its DAC (which in turn is controlled by the output of
the translator).
At power-on or reset, the translator sets the DACs and the phase
current polarity to the initial Home state (shown in figures 8
through 11), and the current regulator to Mixed Decay Mode for
both phases. When a step command signal occurs on the STEP
input, the translator automatically sequences the DACs to the
next level and current polarity. (See table 2 for the current-level
sequence.) The microstep resolution is set by the combined effect
of the MSx inputs , as shown in table 1.
When stepping, if the new output levels of the DACs are lower
than their previous output levels, then the decay mode for the
active full-bridge is set to Mixed. If the new output levels of the
DACs are higher than or equal to their previous levels, then the
decay mode for the active full-bridge is set to Slow. This auto-
matic current decay selection improves microstepping perfor-
mance by reducing the distortion of the current waveform that
results from the back EMF of the motor.
Microstep Select (MSx). The microstep resolution is set by
the voltage on logic inputs MSx, as shown in table 1. The MS1 pin
has a 100 k Ω pull-down resistance, and the MS2 pin has a 50 k Ω
pull-down resistance. When changing the step mode the change
does not take effect until the next STEP rising edge.
If the step mode is changed without a translator reset, and abso-
lute position must be maintained, it is important to change the
step mode at a step position that is common to both step modes in
order to avoid missing steps. When the device is powered down,
or reset due to TSD or an over current event the translator is set to
the home position which is by default common to all step modes.
Mixed Decay Operation. The bridge operates in Mixed
decay mode, at power-on and reset, and during normal running
according to the ROSC configuration and the step sequence, as
shown in figures 8 through 11. During Mixed decay, when the trip
point is reached, the A4984 initially goes into a fast decay mode
for 31.25% of the off-time, t OFF . After that, it switches to Slow
decay mode for the remainder of t OFF . A timing diagram for this
feature appears on the next page.
Typically, mixed decay is only necessary when the current in the
winding is going from a higher value to a lower value as determined
by the state of the translator. For most loads automatically-selected
mixed decay is convenient because it minimizes ripple when the
current is rising and prevents missed steps when the current is falling.
For some applications where microstepping at very low speeds is
necessary, the lack of back EMF in the winding causes the current to
increase in the load quickly, resulting in missed steps. This is shown
in figure 2. By pulling the ROSC pin to ground, mixed decay is set to
be active 100% of the time, for both rising and falling currents, and
prevents missed steps as shown in figure 3. If this is not an issue, it
is recommended that automatically-selected mixed decay be used,
because it will produce reduced ripple currents. Refer to the Fixed
Off-Time section for details.
Low Current Microstepping. Intended for applications
where the minimum on-time prevents the output current from
regulating to the programmed current level at low current steps.
To prevent this, the device can be set to operate in Mixed decay
mode on both rising and falling portions of the current waveform.
This feature is implemented by shorting the ROSC pin to ground.
In this state, the off-time is internally set to 30 μ s.
Reset Input (ˉRˉ ˉEˉ ˉSˉ ˉEˉ ˉTˉ ). The ˉRˉ ˉEˉ ˉS ˉEˉ ˉTˉ input sets the translator
to a predefined Home state (shown in figures 8 through 11), and
turns off all of the FET outputs. All STEP inputs are ignored until
the ˉRˉ ˉEˉ ˉS ˉEˉ ˉTˉ input is set to high.
Step Input (STEP) . A low-to-high transition on the STEP
input sequences the translator and advances the motor one incre-
ment. The translator controls the input to the DACs and the direc-
tion of current flow in each winding. The size of the increment is
determined by the combined state of the MSx inputs.
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| A4985SETTR-T | IC STEPPER MOTOR DRIVER 32QFN |
| A4986SLPTR-T | IC PWM MOTOR DRIVER 24TSSOP |
| A4987SLPTR-T | IC STEPPER MOTOR DRIVER 24TSSOP |
| A4988SETTR-T | IC MICROSTEPPER MOTOR DRVR 28QFN |
| A4989SLDTR-T | IC FULL BRDG MFET DRVR 38TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A4985 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Microstepping Driver with Translator And Overcurrent Protection |
| A4985_12 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Microstepping Driver with Translator And Overcurrent Protection |
| A49854-000 | 制造商:TE Connectivity 功能描述:7528L1024-0 |
| A4985SESTR-T | 功能描述:IC STEPPER MOTOR DRIVER 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:步进电机驱动器，1-2 相，2 相 评估套件:- 输出数:1 电流 - 输出:800mA 电压 - 负载:10 V ~ 28 V 电源电压:4.75 V ~ 5.25 V 工作温度:-20°C ~ 90°C 安装类型:表面贴装 封装/外壳:28-SOP + 2 翼片裸露焊盘 供应商设备封装:28-HSOPHC（15.2x7.9） 包装:剪切带 (CT) 其它名称:869-1268-1 |
| A4985SETTR-T | 功能描述:IC STEPPER MOTOR DRIVER 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:步进电机驱动器，1-2 相，2 相 评估套件:- 输出数:1 电流 - 输出:800mA 电压 - 负载:10 V ~ 28 V 电源电压:4.75 V ~ 5.25 V 工作温度:-20°C ~ 90°C 安装类型:表面贴装 封装/外壳:28-SOP + 2 翼片裸露焊盘 供应商设备封装:28-HSOPHC（15.2x7.9） 包装:剪切带 (CT) 其它名称:869-1268-1 |
发布紧急采购，3分钟左右您将得到回复。