- 您现在的位置：买卖IC网 > Datasheet目录306 > A6268KLPTR-T (Allegro Microsystems Inc)IC LED CTLR AUTOMOBILE 16TSSOP Datasheet资料下载
参数资料
| 型号： | A6268KLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 15/19页 |
| 文件大小： | 0K |
| 描述： | IC LED CTLR AUTOMOBILE 16TSSOP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | 低端，PWM，SEPIC，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 车载，背光 |
| 频率： | 100kHz ~ 700kHz |
| 电源电压： | 5 V ~ 50 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 150°C |
| 其它名称： | 620-1473-6 |
A6268
Automotive High Current LED Controller
Application Information
Component Selection
External component selection is critical to the successful appli-
cation of the LED driver. Although the inductor, the switching
MOSFET, and the output capacitor are the most critical elements,
the specification of the rectifying diode and sense resistors should
also be carefully considered.
In boost mode, the power loss in the current sense resistor is
worse at the lowest input voltage:
P LOSS = ( V LED / V IN (min) ) × R LS × I 2LED (16)
In buck-boost mode, the power loss in the current sense resistor is
worse at the lowest input voltage:
The starting point for component selection is to define the maxi-
P LOSS = ( [ V IN + V LED ] / V IN ) × R LS × I 2LED
(17)
mum LED current, the voltage across the LEDs, and the input
operating voltage range. This then allows the average inductor
current under worst case conditions to be calculated.
The inductor value is then selected based on the acceptable
inductor ripple current. The amount of ripple current will then
determine the maximum inductor current under worst case condi-
tions. From this current the switch current sense resistor can be
calculated.
LED Current Sense Resistor (R LS ) If the voltage at the
IREF pin, V IREF , is greater than 1 V, or if IREF is tied to VREG,
then the value of the LED current sense resistor, R LS , can be
calculated from:
R LS = V IDL / I LED (max) (14)
where V IDL is the differential voltage across the LED current
sense amplifier and I LED (max) is the maximum LED current.
If V IREF is less than 1 V, then the value of the LED current sense
resistor can be calculated from:
The power rating of the sense resistor should exceed the above
rating at the maximum temperature.
The resistors should be of a low inductance construction. Surface
mount chip resistors are usually the most suitable, however, axial
or radial leaded resistors can be used provided that the lead length
is kept to a minimum.
Inductor Selection Selecting the correct inductance is a
balance between choosing a value that is small enough to help
reduce size and cost, but high enough to ensure that the inductor
current ripple is kept to an acceptable level. A reasonable target
for the ripple current is 20% of the maximum average current.
The inductor current equations differ slightly depending on
whether the A6268 is configured as a boost or as a buck-boost
converter.
? In a boost converter configuration:
? The maximum average inductor current is approximately:
R LS = V IREF / (10 × I LED (max) ) (15)
The typical value for V IDL is 100 mV. Examples of various sense
resistor values are given in table 2.
I L(av) (max) = I LED (max) × V LED / V IN (min)
? The inductor current ripple is approximately:
I LRIP = V IN × ( V LED – V IN ) / ( f OSC × L × V LED )
? The inductor value is therefore:
(18)
(19)
Table 2. Sense Resistor Values
L = V IN × ( V LED – V IN ) / ( f OSC × I LRIP × V LED ) (20)
I LED (max)
(mA)
350
700
1000
R LS
(m Ω )
286
143
100
? In a buck-boost configuration:
? The maximum average inductor current is approximately:
I L(av) (max) = I LED (max) × ( V IN (min) + V LED ) / V IN (min) (21)
? The inductor current ripple is approximately:
I LRIP = V IN × V LED / ( f OSC × L × [ V IN + V LED ] )
(22)
15
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相关PDF资料 |
PDF描述 |
|---|---|
| A6280EA-T | IC LED DRIVER PWM CONTROL 16-DIP |
| A6281EESTR-T | IC LED DRIVER PWM CONTROL 16-QFN |
| A6282ELPTR-T | IC LED DRIVER LINEAR 24-TSSOP |
| A8431EEHTR-T | IC LED DRVR WHITE BCKLGHT 6-MLP |
| A8500EECTR-T | IC LED DRVR WHT/RGB BCKLGT 26QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A6269 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Automotive LED Array Driver |
| A6269KLJTR-T | 制造商:Allegro MicroSystems 功能描述:TWO CHANNEL LINEAR LED DRIVER 制造商:ALLEGRO MICROSYSTEMS, LLC 功能描述:IC LED DRVR AUTOMOTIVE 8SOICN |
| A626A | 功能描述:ADAPTER PROGRAMMER 32-SSOP RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
| A62710-000 | 制造商:TE Connectivity 功能描述:TXR21AB00-0805BI |
| A6271KLPTR-T | 功能描述:LED Driver IC 1 Output DC DC Controller SEPIC, Step-Down (Buck), Step-Up (Boost) Analog, Internal or External PWM Dimming 16-eTSSOP 制造商:allegro microsystems, llc 系列:汽车级，AEC-Q100 包装:剪切带（CT） 零件状态:有效 类型:DC DC 控制器 拓扑:SEPIC，降压（降压），升压（升压） 内部开关:无 输出数:1 电压 - 供电（最低）:4.2V 电压 -?供电（最高）:50V 电压 - 输出:- 电流 - 输出/通道:- 频率:700kHz 调光:模拟，PWM 应用:汽车级 工作温度:-40°C ~ 150°C（TJ） 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽）裸焊盘 供应商器件封装:16-eTSSOP 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。