- 您现在的位置：买卖IC网 > Datasheet目录306 > A6268KLPTR-T (Allegro Microsystems Inc)IC LED CTLR AUTOMOBILE 16TSSOP Datasheet资料下载
参数资料
| 型号： | A6268KLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 9/19页 |
| 文件大小： | 0K |
| 描述： | IC LED CTLR AUTOMOBILE 16TSSOP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | 低端，PWM，SEPIC，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 车载，背光 |
| 频率： | 100kHz ~ 700kHz |
| 电源电压： | 5 V ~ 50 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 150°C |
| 其它名称： | 620-1473-6 |
A6268
Automotive High Current LED Controller
LF Single diode forward voltage reference input. Measures the
forward voltage of the first LED. This value is used as a reference
against the voltage on the LA pin to detect possible shorted LEDs
in the LED string.
Circuit Operation
Converter A constant frequency, current mode control scheme
is used to regulate the current through the LEDs. There are two
control loops within the regulator. The inner loop formed by the
amplifier, AS (see the Functional Block Diagram for AS, AC, AE,
and AL), comparator, AC, and the RS bistable, controls the induc-
tor current as measured through the switch by the switch sense
resistor, R SS .
The outer loop including the amplifier, AL, and the integrating
error amplifier, AE, controls the average LED current by provid-
ing a setpoint reference for the inner loop.
The LED current is measured by the LED sense resistor, R SL ,
and compared to the internal reference current to produce an
integrated error signal at the output of AE. This error signal sets
the average amount of energy required from the inductor by the
LEDs. The average inductor energy transferred to the LEDs is
defined by the average inductor current as determined by the
inner control loop.
The inner loop establishes the average inductor current by
controlling the peak switch current on a cycle-by-cycle basis.
Because the relationship between peak current and average cur-
rent is non-linear, depending on the duty cycle, the reference
level for the peak switch current is modified by a slope generator.
This compensation reduces the peak switch current measurement
by a small amount as the duty cycle increases (refer to figure 1).
The slope compensation also removes the instability inherent in a
fixed frequency current control scheme.
The control loops work together as follows: the switch current,
sensed by the switch current sense resistor, R SS , is compared
to the LED current error signal. As the LED current increases
the output of AE will reduce, reducing the peak switch current
and thus the current delivered to the LEDs. As the LED current
decreases the output of AE increases, increasing the peak switch
current and thus increasing the current delivered to the LEDs.
known as discontinuous mode operation, and results in some low
frequency ripple. The average LED current, however, remains
regulated down to zero. In discontinuous mode, when the induc-
tor current drops to zero, the voltage at the drain of the external
MOSFET rings, due to the resonant LC circuit formed by the
inductor, and the switch and diode capacitance. This ringing is
low frequency and is not harmful.
Switch Current Limit The switch current is measured by the
switch sense resistor, R SS , and the switch sense amplifier, AS
(see the Functional Block Diagram). The input limit of the sense
amplifier, V IDS , and the maximum switch current, I SMAX , define
the maximum value of the sense resistor as:
R SS = V IDS / I SMAX (1)
This defines the maximum measurable value of the switch (and
inductor) current.
The maximum switch current is modulated by the on-time of the
switch. An internal slope compensation signal is subtracted from
the voltage sense signal to produce a peak sense voltage which
effectively defines the current limit. This signal is applied at a
rate of –16 mV / μ s starting with no contribution (t = 0 μ s) at the
beginning of each switching cycle. Figure 1 illustrates how the
peak sense voltage (typical values) changes over a period of 3 μ s.
For example, the maximum current (typical) through the switch
at t = 1.5 μ s (D = 50%) would be 145 mV/R SS , however, if the
switch remained on for a further 1 μ s, the maximum current
through the switch would be 129 mV/R SS .
200
150
100
50
0
Under some conditions, especially when the LED current is set to
a low value, the energy required in the inductor may result in the
0
1
Period ( μ s)
2
3
inductor current dropping to zero for part of each cycle. This is
Figure 1. Slope compensation for peak switch current control.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| A6280EA-T | IC LED DRIVER PWM CONTROL 16-DIP |
| A6281EESTR-T | IC LED DRIVER PWM CONTROL 16-QFN |
| A6282ELPTR-T | IC LED DRIVER LINEAR 24-TSSOP |
| A8431EEHTR-T | IC LED DRVR WHITE BCKLGHT 6-MLP |
| A8500EECTR-T | IC LED DRVR WHT/RGB BCKLGT 26QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A6269 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Automotive LED Array Driver |
| A6269KLJTR-T | 制造商:Allegro MicroSystems 功能描述:TWO CHANNEL LINEAR LED DRIVER 制造商:ALLEGRO MICROSYSTEMS, LLC 功能描述:IC LED DRVR AUTOMOTIVE 8SOICN |
| A626A | 功能描述:ADAPTER PROGRAMMER 32-SSOP RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
| A62710-000 | 制造商:TE Connectivity 功能描述:TXR21AB00-0805BI |
| A6271KLPTR-T | 功能描述:LED Driver IC 1 Output DC DC Controller SEPIC, Step-Down (Buck), Step-Up (Boost) Analog, Internal or External PWM Dimming 16-eTSSOP 制造商:allegro microsystems, llc 系列:汽车级，AEC-Q100 包装:剪切带（CT） 零件状态:有效 类型:DC DC 控制器 拓扑:SEPIC，降压（降压），升压（升压） 内部开关:无 输出数:1 电压 - 供电（最低）:4.2V 电压 -?供电（最高）:50V 电压 - 输出:- 电流 - 输出/通道:- 频率:700kHz 调光:模拟，PWM 应用:汽车级 工作温度:-40°C ~ 150°C（TJ） 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽）裸焊盘 供应商器件封装:16-eTSSOP 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。