- 您现在的位置：买卖IC网 > PDF目录1774 > A8291SETTR-T (Allegro Microsystems Inc)IC VOLTAGE REG SGL LNB 28-QFN PDF资料下载
参数资料
| 型号： | A8291SETTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 14/19页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE REG SGL LNB 28-QFN |
| 标准包装： | 9,000 |
| 应用： | 转换器，模拟和数字式卫星信号接收器 |
| 输入电压： | 8 V ~ 16 V |
| 输出数： | 1 |
| 输出电压： | 12.7 V ~ 20.4 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-VFQFN 裸露焊盘 |
| 供应商设备封装： | 28-QFN/MLP 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
A8291
Single LNB Supply and Control Voltage Regulator
Status Registers (I 2 C?-Compatible Read Register)
The main fault conditions: overcurrent (OCP), under voltage
(VUV) and overtemperature (TSD), are all indicated by setting
the relevant bits in the Status registers. In all fault cases, once the
bit is set, it remains latched until the A8291 is read by the I 2 C?
master, assuming the fault has been resolved.
The current status of the LNB output is indicated by the dis-
able bit, DIS. The DIS bit is set when either a fault occurs or if
the LNB is disabled intentionally. This bit is latched, and is reset
when the LNB is commanded on again. The power not good
(PNG), tone detect (TDET), and cable disconnected (CAD) flags
are the only bits which may be reset without an I 2 C? read se-
quence. Table 5 summarizes the condition of each bit when set and
how it is reset.
Table 5. Status Register Bit Setting
As the A8291 has a comprehensive set of status reporting bits,
it is necessary to have two Status registers. When performing a
multiple read function, register 1 is read followed by register 2,
then register 1 again and so on. Whenever a new read function is
performed, register 1 is always read first.
The normal sequence of the master in a fault condition will be
to detect the fault by reading the Status registers, then rereading
the Status registers until the status bit is reset indicating the fault
condition is reset. The fault may be detected either by continuously
polling, by responding to an interrupt request (IRQ), or by detect-
ing a fault condition externally and performing a diagnostic poll of
all slave devices. Note that the fully-operational condition of the
Status registers is all 0s, to simplify checking of the Status bit.
Status Bit
CAD
DIS
OCP
PNG
TDET
TSD
VUV
Function
Cable disconnected
LNB disabled, either intentionally or
due to fault
Overcurrent
Power not good
Tone detect
Thermal shutdown
Undervoltage
Set
Non-latched
Latched
Latched
Non-latched
Non-latched
Latched
Latched
Reset
Condition
Cable disconnect test off or
cable connected
LNB enabled and no fault
I 2 C? read and fault removed
LNB volts in range
Tone removed
I 2 C? read and fault removed
I 2 C? read and fault removed
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
14
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
相关PDF资料 |
PDF描述 |
|---|---|
| A8292SETTR-T | IC REG LNB SUPPLY/CONTROL 28-MLP |
| A8293SETTR-T | IC REG LNB BOOST/LINEAR 28QFN |
| A8436EEJTR-T | IC PHOTOFLASH CHARGER 10-MLP |
| A8437ECGLT | IC PHOTOFLASH CAP CHARGER WLCSP |
| A8438EEJTR-T | IC PHOTOFLASH CHARGER 10-MLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A8291SETTR-TB | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Single LNB Supply and Control Voltage Regulator |
| A8292 | 制造商:AMPEX 功能描述: |
| A8292SETTR-T | 功能描述:IC REG LNB SUPPLY/CONTROL 28-MLP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| A8293 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Single LNB Supply and Control Voltage Regulator |
| A8293SESTR-T | 功能描述:IC REG LNB BOOST/LINEAR 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。