- 您现在的位置：买卖IC网 > Datasheet目录306 > A8431EEHTR-T (Allegro Microsystems Inc)IC LED DRVR WHITE BCKLGHT 6-MLP Datasheet资料下载
参数资料
| 型号： | A8431EEHTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 7/11页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGHT 6-MLP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1.2MHz |
| 电源电压： | 2.5 V ~ 10 V |
| 输出电压： | 32V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WFDFN 裸露焊盘 |
| 供应商设备封装： | 6-MLP/DFN（2x3） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | 620-1195-6 |
A8431
White LED Driver Constant Current
Step-up Converter
Device Operation
The A8431 uses a constant-frequency, current-mode control
scheme to regulate the current through the load. The load
current produces a voltage across the external sense resistor
(R1 in schematic 1) and the input at the FB pin. This voltage
is then compared to the internal 95 mV reference to produce
an error signal. The switch current is sensed by the internal
sense resistor and compared to the load current error signal.
As the load current increases, the error signal diminishes,
reducing the maximum switch current and thus the current
delivered to the load. As the load current decreases, the
error signal rises, increasing the maximum switch current
and thus increasing the current delivered to the load.
To set the load current, ensure that the required internal
reference value of 95 mV is produced at the desired load. To
do so, select a resistance value for the sense resistor, R1 ( Ω ),
such that:
R1 = 95 mV ? I LOAD
where I LOAD is the target load current (mA).
The table below shows typical values for R1. Note that the
resistance value is from the standard E96 series.
As load current is reduced, the energy required in the
inductor, L1, diminishes, resulting in the inductor current
dropping to 0 A for low load-current levels. This is known
Power Dissipation versus I OUT
as Discontinuous mode operation, and results in some low-
frequency ripple. The average load current, however, remains
regulated down to 0 A.
In Discontinuous mode, when the inductor current drops to
0 A, the voltage at the SW pin rings, due to the capacitance
in the resonant LC circuit formed by the inductor and the
capacitance of the switch and the diode. This ringing is
low-frequency and is not harmful. It can be damped with a
resistor across the inductor, but this reduces efficiency and is
not recommended.
Overvoltage Protection
An overvoltage event can occur when the LEDs become
disconnected or fail in an open state. In these cases, the
current flow through the sense resistor, R1, becomes 0 A and
thus the feedback voltage, V FB becomes 0 V. The A8431
compensates by increasing the on time of the switch, which
increases the output voltage.
The A8431 has built-in protection to guard against excessive
voltage on the SW pin. If the output voltage exceeds the
typical level of the Output Overvoltage Rising Limit, V OVPR ,
then the overvoltage protection circuitry shuts off the internal
switch until the output voltage falls below the Output
Overvoltage Falling Limit, V OVPF . At this point, the A8431
operates normally. There is no need for an external Zener
diode for the A8431.
120
110
100
90
80
70
60
50
40
30
20
10
0
Target Load Current
( I LOAD )
(mA)
5
10
12
15
Sense Resistor (R1)
( Ω )
19.1
9.53
7.87
6.34
5
10
15
I OUT (mA)
20
25
20
4.75
Vin = 3V, 3 LED
Vin = 5V, 3 LED
Vin = 3V, 4 LED
Vin = 5V, 4 LED
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
6
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
相关PDF资料 |
PDF描述 |
|---|---|
| A8500EECTR-T | IC LED DRVR WHT/RGB BCKLGT 26QFN |
| A8502KLPTR-T | IC LED DVR WHITE MULTI 16-TSSOP |
| A8504EECTR-T | IC LED DRVR WHT/RGB BCKLGT 26QFN |
| A8507ELBTR-T | IC DRIVER WLED/RGB 24-SOIC |
| A8508GLPTR-T | IC LED DVR WHITE 8X120MA 24TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A84334-000 | 制造商:TE Connectivity 功能描述:VARISTOR 470VDC 5MM 10% LEADED 制造商:TE Connectivity 功能描述:VARISTOR 470V 400A DISC 5MM |
| A8434 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:6-Channel High Efficiency Charge Pump White LED Driver |
| A8434EESTR-T | 功能描述:IC LED DRVR WHITE BCKLGHT 16-MLP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| A8435 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:High Efficiency Charge Pump White LED Driver |
| A8435EESTR-T | 功能描述:IC LED DRVR WHITE BCKLGHT 16-MLP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT |
发布紧急采购，3分钟左右您将得到回复。