- 您现在的位置：买卖IC网 > Datasheet目录306 > A8431EEHTR-T (Allegro Microsystems Inc)IC LED DRVR WHITE BCKLGHT 6-MLP Datasheet资料下载
参数资料
| 型号： | A8431EEHTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGHT 6-MLP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1.2MHz |
| 电源电压： | 2.5 V ~ 10 V |
| 输出电压： | 32V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WFDFN 裸露焊盘 |
| 供应商设备封装： | 6-MLP/DFN（2x3） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | 620-1195-6 |
A8431
White LED Driver Constant Current
Step-up Converter
Application Information
Component Selection
The component values shown in schematic 1 are sufficient
for most applications. To reduce the output ripple, L1 may be
increased, but in most cases this results in excessive board
area and cost.
Inductor Selection . With an internal PWM frequency of
1.2 MHz, the optimal L1 value for most cases is 22 μ H.
For worst case conditions (high output voltage and current
and low input voltage), the inductor should be rated at the
switch current limit, I SWLIM . If high temperature operation
is required, a derating factor will have to be considered. In
some cases, where lower inductor currents are expected,
the current rating can be decreased. Several inductor
manufacturers, including: Coilcraft, Murata, Panasonic,
Sumida, Taiyo Yuden, and TDK, have and are developing
suitable small-size inductors.
Diode Selection . The diode should have a low forward
voltage to reduce conduction losses. In addition, it should
have a low capacitance to reduce switching losses. Schottky
diodes can provide both these features, if carefully
selected. The forward voltage drop is a natural advantage
for Schottky diodes, and it reduces as the current rating
increases. However, as the current rating increases, the
diode capacitance also increases. As a result, the optimal
selection is usually the lowest current rating above the circuit
maximum. In this application, a current rating in the range
from 100 mA to 200 mA is usually sufficient.
conditions. Suitable capacitors are available from TDK,
Taiyo Yuden, Murata, Kemet, and AVX.
Dimming Control
LED brightness can be controlled either: (a) by modify-
ing the voltage at the top of R1 to control the LED current,
I LOAD , directly, or (b) by using a PWM signal on the EN pin
to chop the output.
Feedback Modulation . By adding a voltage drop between
the FB pin and R1, as shown in schematic 2, the LED
current, I LOAD , can be made to decrease. As V C (control
voltage) increases, the voltage drop across R2 also increases.
This causes the voltage at FB to increase, and the A8431
reduces I LOAD to compensate. As V C increases further, the
current drops to 0 A, and R2 maintains the full 95 mV on FB.
Reducing V C diminishes the voltage across R2 until, when
V C is at 95 mV, there is no drop across R2 and the current
level is defined by R1. Reducing V C below 95 mV causes
I LOAD to increase further, due to the voltage drop across R2
in the reverse direction. This continues until, when V C is at
0 V, there is approximately 5 mV across R2. At that point,
I LOAD (mA), is defined as:
I LOAD = 100 mV ? R1
where R1 is the resistance of the sense resistor ( Ω ).
Capacitor Selection . Because the capacitor values are low,
ceramic capacitors are the best choice for this application.
To reduce performance variation as temperature changes,
6
VIN
L1
22 μH
1
SW
D1
OVP
low- drift capacitor types, such as X7R and X5R, should
be used. A 1.0 μ F capacitor on the VIN pin is suitable for
most applications. In cases where large inductor currents
are switched, a larger capacitor may be needed. The
output capacitor, C2, can be as small as 0.22 μ F for most
applications and most input/output voltage ranges. Increasing
the capacitor value on the output aids in increasing the
Li-ion
2.5 V to
4.2 V
C1
1.0 μF
EN
4
Enable
A8431
GND
2
V C
5
FB
3
R2
5 k Ω
R3
90 k Ω
R1
6.3 Ω
C2
0.22 μF
efficiency of low input voltage/high output voltage
Schematic 2. Dimming control with dc voltage
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| A8500EECTR-T | IC LED DRVR WHT/RGB BCKLGT 26QFN |
| A8502KLPTR-T | IC LED DVR WHITE MULTI 16-TSSOP |
| A8504EECTR-T | IC LED DRVR WHT/RGB BCKLGT 26QFN |
| A8507ELBTR-T | IC DRIVER WLED/RGB 24-SOIC |
| A8508GLPTR-T | IC LED DVR WHITE 8X120MA 24TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A84334-000 | 制造商:TE Connectivity 功能描述:VARISTOR 470VDC 5MM 10% LEADED 制造商:TE Connectivity 功能描述:VARISTOR 470V 400A DISC 5MM |
| A8434 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:6-Channel High Efficiency Charge Pump White LED Driver |
| A8434EESTR-T | 功能描述:IC LED DRVR WHITE BCKLGHT 16-MLP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| A8435 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:High Efficiency Charge Pump White LED Driver |
| A8435EESTR-T | 功能描述:IC LED DRVR WHITE BCKLGHT 16-MLP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT |
发布紧急采购，3分钟左右您将得到回复。