- 您现在的位置：买卖IC网 > Datasheet目录307 > A8516ELPTR-T (Allegro Microsystems Inc)IC LED DVR BACKLIGHT MON 24TSSOP Datasheet资料下载
参数资料
| 型号： | A8516ELPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 12/17页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR BACKLIGHT MON 24TSSOP |
| 标准包装： | 8,000 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 6 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 300kHz ~ 1MHz |
| 电源电压： | 8 V ~ 24 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 24-TSSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
A8516
LED Backlight Driver for LCD Monitors and Televisions
Startup Sequence When EN is pulled high, the IC enters
soft start. The IC first tries to determine which LEDx pins are
being used, by raising the LEDx pin voltage with a small current.
After a duration of 512 switching cycles, the LEDx pin voltage
is checked. Any LEDx channel with a drain voltage smaller then
100 mV is removed from the control loop. This is the reason why
unused LEDx pins should be connected to GND,
After the first PWM positive trigger, the boost current is limited
to 30% of normal value and all active LEDx pins sink 1 / 12 of
the set current until output voltage reaches sufficient regulation
level. When the device comes out of soft start, boost current and
the LEDx pin currents are set to normal operating level. Within
a few cycles, the output capacitor charges to the voltage required
to supply full LEDx current. After output voltage, V OUT , reaches
the required level, LEDx current toggles between 0% and 100%
with each PWM command signal.
In case of a heavy overload on V OUT at startup, the device will
stay in soft start mode indefinitely, as the output voltage cannot
rise to the LED regulation level.
LED Short Detect Any LEDx pins that have a voltage exceed-
ing the Short Circuit Detect Voltage, V SC , cause the device to
shut down and this condition is latched. This faults occurs when
multiple LEDs short. In case only a few LEDs short, the IC will
continue to work as long as power dissipation in the IC is limited.
Overvoltage Protection The A8516 has an adjustable over-
voltage protection feature to protect the power components
(external MOSFET, output diode and capacitors) against output
overvoltage. The overvoltage level can be set, from 19.5 V to a
higher voltage, with an external resistor, R OVP . When the current
though the OVP pin exceeds 200 μ A, internal OVP comparator
goes high and the device shuts down. The OVP fault disables all
LEDx strings that are below regulation, thus preventing them
from controlling the boost output voltage.
Calculate the value for R OVP ( Ω ) as follows:
R OVP = ( V OVP – 19.5) / 200 μ A , (5)
where V OVP is the required OVP level in V.
For single-IC operation, select R OVP such that its OVP setpoint is
approximately 10 V above the LED operating voltage at cold. For
example, given the pin regulation voltage, V LEDx of 1.4 V (typ.), if
LED V F = 3.4 V (max.) and there are 15 LEDs in series, then the
operating voltage is approximately:
V OUT = 3.4 V × 15 + 1.4 V = 52.4 V .
In this case, select OVP at about 60 V, which gives R OVP = 200 k Ω .
Open LED Protection During normal operation, if any enabled
LED string opens, voltage on the corresponding LEDx pin goes
to zero. The boost loop operates in open loop till the OVP level
is reached. The A8516 identifies the open LED string when over-
voltage is detected. Open strings are then removed from the regu-
lation loop. Afterwards, the boost controller operates in normal
manner, and the output voltage is regulated to drive the remaining
strings. If the open LED string is reconnected, it will sink current
up to the programmed current level.
Note: Open strings are removed from boost regulation, but not
disabled. This keeps the string in operation if LEDs open for only
a short length of time, or reach OVP level on a transient event.
The disconnected string can be restored to normal mode by reen-
abling the IC. It can also be restored to normal operation if the
fault is removed from the corresponding LEDx pin, but an OVP
event occurs on any other LEDx pin.
Overcurrent Protection The IC provides pulse-by-pulse
current limiting for the boost MOSFET. The current limit level,
I SC (A), can be set by selecting the external resistor, R SC ( Ω ):
R SC = 0.095 / I SC . (6)
If the boost output voltage is unable to reach the regulation target
even when the switch is operating at maximum current limit, the
boost control loop will force the compensating capacitor, C COMP ,
to rise in voltage until it reaches the overcurrent fault level
(3.4 V approximately). The overcurrent fault forces the device
into soft start.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
12
相关PDF资料 |
PDF描述 |
|---|---|
| A8740EEETR-T | IC PHOTOFLASH CAP CHARGER 8DFN |
| AC162049-2 | MOD PROGR UNIV MPLAB ICD2 ICD3 |
| AC162049 | MODULE SOCKET FOR ICD2 DIP |
| AC163020 | ADAPTER PROGRAMMER PIC10F2XX |
| AC164032 | ADAPTER PICSTART PLUS 8DFN/DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A8517KLPTR-T | 功能描述:LED 驱动器 IC 10 输出 DC DC 稳压器 升压（升压） PWM 调光 60mA 28-TSSOP-EP 制造商:allegro microsystems, llc 系列:汽车级，AEC-Q100 包装:剪切带（CT） 零件状态:停产 类型:DC DC 稳压器 拓扑:升压（升压） 内部开关:是 输出数:10 电压 - 供电（最低）:4.5V 电压 -?供电（最高）:36V 电压 - 输出:- 电流 - 输出/通道:60mA 频率:400kHz ~ 2.3MHz 调光:PWM 应用:汽车级 工作温度:-40°C ~ 125°C（TA） 安装类型:表面贴装 封装/外壳:28-SOIC（0.173"，4.40mm 宽）裸露焊盘 供应商器件封装:28-TSSOP-EP 标准包装:1 |
| A8518KLPTR-T | 功能描述:LED 驱动器 IC 2 输出 DC DC 稳压器 升压（升压） 模拟，PWM 调光 200mA 16-TSSOP-EP 制造商:allegro microsystems, llc 系列:汽车级，AEC-Q100 包装:剪切带（CT） 零件状态:有效 类型:DC DC 稳压器 拓扑:升压（升压） 内部开关:是 输出数:2 电压 - 供电（最低）:4.5V 电压 -?供电（最高）:40V 电压 - 输出:40V 电流 - 输出/通道:200mA 频率:2.15MHz 调光:模拟，PWM 应用:背光 工作温度:-40°C ~ 125°C（TA） 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽）裸焊盘 供应商器件封装:16-TSSOP-EP 标准包装:1 |
| A8518KLPTR-T-1 | 功能描述:AUTOMOTIVE TWO STRING BOOST LED 制造商:allegro microsystems, llc 系列:* 零件状态:在售 标准包装:4,000 |
| A85192-1 | 功能描述:电线鉴定 CALIBRATION LABELS REORDER # AP01371 RoHS:否 制造商:TE Connectivity / Q-Cees 产品:Labels and Signs 类型: 材料:Vinyl 颜色:Blue 宽度:0.625 in 长度:1 in |
| A8519KETTR-R | 功能描述:LED 驱动器 IC 4 输出 DC DC 稳压器 升压（升压） 模拟，PWM 调光 100mA 28-QFN-EP（5x5） 制造商:allegro microsystems, llc 系列:汽车级，AEC-Q100 包装:剪切带（CT） 零件状态:有效 类型:DC DC 稳压器 拓扑:升压（升压） 内部开关:是 输出数:4 电压 - 供电（最低）:4.5V 电压 -?供电（最高）:40V 电压 - 输出:40V 电流 - 输出/通道:100mA 频率:200kHz ~ 2.15MHz 调光:模拟，PWM 应用:汽车级，背光 工作温度:-40°C ~ 125°C（TA） 安装类型:表面贴装 封装/外壳:28-VFQFN 裸露焊盘 供应商器件封装:28-QFN-EP（5x5） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。