参数资料
型号: AB-091
英文描述: AB-091 - VOLTAGE-FEEDBACK AMPLIFIERS vs CURRENT-FEEDBACK AMPLIFIERS: BANDWIDTH AND DISTORTION CONSIDERATIONS
中文描述: 抗体- 091 -电压反馈放大器队电流反馈放大器:带宽和变形的考虑因素
文件页数: 2/2页
文件大小: 22K
代理商: AB-091
2
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
In the clamping mode, when the voltage across the two
zeners reaches
±
(V
Z
+ V
F
), the circuit goes from acting as a
voltage amplifier to acting as a voltage reference; the volt-
age across R
is fixed and the potentiometer output is
±
x(V
Z
+V
F
). Further increase in the magnitude of the signal at E
I
can’t change this potentiometer value until it drops below
the limit point V
L
.
Thus, clamping is no longer limited to the fixed levels of
available zener voltages. Even clamping levels as low as
5mV become practical when offset-trimmable OPA111 op
amps replace the OPA2111. However, available zener volt-
ages and the closed-loop gain of A
2
set the maximum
clamping level.
Use of 10 –V zeners and a gain of one for A
can cover the
voltage range of most analog-signal processing. Unfortu-
nately, the voltage temperature coefficients of 10 –V zeners
would produce thermal drift in the clamping level. With 5.6
–V zeners, however, the temperature coefficients of the
zener and forward voltages tend to cancel. For such zener
diodes V
+ V
= 6.2V, and the net drift is near zero. Then,
with A
2
set to a gain of 1.77, the maximum limit voltage V
L
is 11V.
The 5% tolerances of the zener voltages determine the basic
accuracy of the clamp levels. The gain-setting resistors R
2
and R
impose additional tolerance error. However, adjust-
ing the gain with these resistors can compensate for any
zener-voltage error and resistor tolerances. With matched
zeners, the adjustment can readily reduce the clamp-level
errors to less than 1%. Without matching, the 5% error of
simple zener clamping prevails, but the circuit still clamps
sharply.
For frequency stability, resistor R
and capacitor C supply a
frequency roll-off in A
. At high frequencies, the capacitor
shorts the output of A
to its inverting input. Then A
and A
2
operate with independent feedback loops, and the overall
circuit requires stability in the individual amplifiers.
相关PDF资料
PDF描述
AB-092 AB-092 - SWOP AMPS SIMPLIFY RF SIGNAL PROCESSING
AB-093 AB-093 - ISOLATION AMPS HIKE ACCURACY AND RELIABILITY
AB-094 AB-094 - TAME PHOTODIODES WITH OP AMP BOOTSTRAP
AB-095 AB-095 - TIPS FOR USING THE ADS78XX FAMILY OF A/D CONVERTERS
AB-096 AB-096 - BUILD A THREE PHASE SINE WAVE GENERATOR WITH THE UAF42
相关代理商/技术参数
参数描述
AB0912DB-Z03 功能描述:鼓风机 12VDC RoHS:否 制造商:Murata 产品:Blowers 电流类型:DC 电源电压:5.3 V 气流:1 l/min 轴承类型: 噪声: 速度: 功率额定值: 框架尺寸 (mm):20 mm x 20 mm x 1.85 mm 外壳材料: 端接类型:SMD/SMT 系列:MZB
AB0912DB-Z03-LF 功能描述:鼓风机 12VDC 92x120mm Ball Bearing RoHS:否 制造商:Murata 产品:Blowers 电流类型:DC 电源电压:5.3 V 气流:1 l/min 轴承类型: 噪声: 速度: 功率额定值: 框架尺寸 (mm):20 mm x 20 mm x 1.85 mm 外壳材料: 端接类型:SMD/SMT 系列:MZB
AB0912MB-Z01 制造商:ADDA USA Corporation 功能描述:12 VDC 29.8 CFM Ball Blower With 10" Leads 94 x 94 x 33 mm
AB0912MB-Z01-LF 功能描述:鼓风机 92mmX33mm 12V RoHS:否 制造商:Murata 产品:Blowers 电流类型:DC 电源电压:5.3 V 气流:1 l/min 轴承类型: 噪声: 速度: 功率额定值: 框架尺寸 (mm):20 mm x 20 mm x 1.85 mm 外壳材料: 端接类型:SMD/SMT 系列:MZB
AB-092 制造商:未知厂家 制造商全称:未知厂家 功能描述:AB-092 - SWOP AMPS SIMPLIFY RF SIGNAL PROCESSING