- 您现在的位置：买卖IC网 > PDF目录364590 > AB-093 AB-093 - ISOLATION AMPS HIKE ACCURACY AND RELIABILITY PDF资料下载
参数资料
| 型号： | AB-093 |
| 元件分类： | 隔离放大器 |
| 英文描述： | AB-093 - ISOLATION AMPS HIKE ACCURACY AND RELIABILITY |
| 中文描述： | 抗体- 093 -分离AMPS二元调涨精确度和可靠性 |
| 文件页数： | 2/2页 |
| 文件大小： | 22K |
| 代理商： | AB-093 |
2
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
In the clamping mode, when the voltage across the two
zeners reaches
±
(V
Z
+ V
F
), the circuit goes from acting as a
voltage amplifier to acting as a voltage reference; the volt-
age across R
is fixed and the potentiometer output is
±
x(V
Z
+V
F
). Further increase in the magnitude of the signal at E
I
can’t change this potentiometer value until it drops below
the limit point V
L
.
Thus, clamping is no longer limited to the fixed levels of
available zener voltages. Even clamping levels as low as
5mV become practical when offset-trimmable OPA111 op
amps replace the OPA2111. However, available zener volt-
ages and the closed-loop gain of A
2
set the maximum
clamping level.
Use of 10 –V zeners and a gain of one for A
can cover the
voltage range of most analog-signal processing. Unfortu-
nately, the voltage temperature coefficients of 10 –V zeners
would produce thermal drift in the clamping level. With 5.6
–V zeners, however, the temperature coefficients of the
zener and forward voltages tend to cancel. For such zener
diodes V
+ V
= 6.2V, and the net drift is near zero. Then,
with A
2
set to a gain of 1.77, the maximum limit voltage V
L
is 11V.
The 5% tolerances of the zener voltages determine the basic
accuracy of the clamp levels. The gain-setting resistors R
2
and R
impose additional tolerance error. However, adjust-
ing the gain with these resistors can compensate for any
zener-voltage error and resistor tolerances. With matched
zeners, the adjustment can readily reduce the clamp-level
errors to less than 1%. Without matching, the 5% error of
simple zener clamping prevails, but the circuit still clamps
sharply.
For frequency stability, resistor R
and capacitor C supply a
frequency roll-off in A
. At high frequencies, the capacitor
shorts the output of A
to its inverting input. Then A
and A
2
operate with independent feedback loops, and the overall
circuit requires stability in the individual amplifiers.
相关PDF资料 |
PDF描述 |
|---|---|
| AB-094 | AB-094 - TAME PHOTODIODES WITH OP AMP BOOTSTRAP |
| AB-095 | AB-095 - TIPS FOR USING THE ADS78XX FAMILY OF A/D CONVERTERS |
| AB-096 | AB-096 - BUILD A THREE PHASE SINE WAVE GENERATOR WITH THE UAF42 |
| AB-097 | AB-097 - DDC101 EVALUATION FIXTURE PC INTERFACE BOARD |
| AB-098 | AB-098 - SELECTING AN A/D CONVERTER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AB-094 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:AB-094 - TAME PHOTODIODES WITH OP AMP BOOTSTRAP |
| AB-095 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:AB-095 - TIPS FOR USING THE ADS78XX FAMILY OF A/D CONVERTERS |
| AB-096 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:AB-096 - BUILD A THREE PHASE SINE WAVE GENERATOR WITH THE UAF42 |
| AB-097 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:AB-097 - DDC101 EVALUATION FIXTURE PC INTERFACE BOARD |
| AB-098 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:AB-098 - SELECTING AN A/D CONVERTER |
发布紧急采购，3分钟左右您将得到回复。