- 您现在的位置：买卖IC网 > PDF目录68990 > ACPM-7813-BLK (AGILENT TECHNOLOGIES INC) 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER PDF资料下载
参数资料
| 型号： | ACPM-7813-BLK |
| 厂商： | AGILENT TECHNOLOGIES INC |
| 元件分类： | 放大器 |
| 英文描述： | 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| 封装： | 4 X 4 MM, 1.10 MM HEIGHT, SMT, 10 PIN |
| 文件页数： | 3/21页 |
| 文件大小： | 183K |
| 代理商： | ACPM-7813-BLK |
11
Design Tips to use Vcntl pin
Power Mode
PA_ON
Vcntl
Power Range
Shut Down
LOW
0V
—
High Power
HIGH
2.5V
≤ 28.5 dBm
To Duplexer
Battery
Vcntl
PA
TxIC
Switch Circuit for PA
Baseband
IC
PA_ON
Enable
Vdd1
Vdd2
Vbias
Vcntl
PMIC or LDO
Note: PMIC: Power Management IC
LDO: Low Drop Output (Regulator)
Power Amplifier Control Using Vcntl
Pin on ACPM-7813
Power amplifier control scheme
in CDMA systems is one of the
important and challenging
aspects of CDMA-based handset
design. Handset designers must
balance maintaining adequate
linearity while optimizing
efficiency at high, medium and
low output power levels. The
primary method to achieve these
goals is to adjust the bias of the
PA as a function of output power.
Theoretically, the best efficiency
would be achieved when the bias
of the PA is continually adjusted
based on the output power
requirement of the PA. However,
implementing this type of circuit
can be complex and costly.
Therefore several different
approaches have been developed
to provide an acceptable trade-
off between optimum efficiency
and optimum manufacturability.
This application section reviews
four methods of controlling the
bias of a CDMA power amplifier:
fixed, step, logical and dynamic.
1. Fixed Bias Control
Using a fixed bias point on the
PA is the traditional method, and
it is the simplest. For example, a
fixed control voltage of 2.5V is
recommended when using
Agilent’s Power Amplifier, 2.5V
Vcntl for ACPM-7813. The Vcntl
pin on the PA is controlled by
PA_ON pin of the baseband IC.
When PA_ON is HIGH, the output
RF signal of the PA is enabled,
enabling the subscriber unit to
transmit the required data. The
switch circuit also controls the
on/off state of the PA.
Below is an example of how to
control the operation of the
ACPM-7813 using the PA_ON and
Vcntl pin of the PA.
相关PDF资料 |
PDF描述 |
|---|---|
| ACPM-7813-TR1 | 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| AD8339ACPZ-R7 | 0 MHz - 50 MHz RF/MICROWAVE I/Q DEMODULATOR |
| AD8339ACPZ-RL | 0 MHz - 50 MHz RF/MICROWAVE I/Q DEMODULATOR |
| AD8339ACPZ | 0 MHz - 50 MHz RF/MICROWAVE I/Q DEMODULATOR |
| ADL5374ACPZ-WP | 3000 MHz - 4000 MHz RF/MICROWAVE QUADRAPHASE MODULATOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ACPM-7813-TR1 | 功能描述:射频放大器 CDMA Amp 824-849MHz RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| ACPM-7821 | 制造商:AVAGO 制造商全称:AVAGO TECHNOLOGIES LIMITED 功能描述:4 x 4 Power Amplifier Module for J-CDMA (898 - 925 MHz) |
| ACPM-7821-BLK | 制造商:AVAGO 制造商全称:AVAGO TECHNOLOGIES LIMITED 功能描述:4 x 4 Power Amplifier Module for J-CDMA (898 - 925 MHz) |
| ACPM-7821-TR1 | 制造商:AVAGO 制造商全称:AVAGO TECHNOLOGIES LIMITED 功能描述:4 x 4 Power Amplifier Module for J-CDMA (898 - 925 MHz) |
| ACPM-7822 | 制造商:AVAGO 制造商全称:AVAGO TECHNOLOGIES LIMITED 功能描述:JCDMA 4x4 Power Amplifier Module (898-925MHz) |
发布紧急采购，3分钟左右您将得到回复。