- 您现在的位置：买卖IC网 > Datasheet目录393 > ACS716KLATR-6BB-NL-T (Allegro Microsystems Inc)IC CURRENT SENSOR 120KHZ 16-SOIC Datasheet资料下载
参数资料
| 型号： | ACS716KLATR-6BB-NL-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 7/22页 |
| 文件大小： | 0K |
| 描述： | IC CURRENT SENSOR 120KHZ 16-SOIC |
| 标准包装： | 1,000 |
| 电流 - 感应： | ±6A |
| 精确度： | ±1.6% |
| 灵敏度： | 151mV/A |
| 电流 - 电源： | 11mA |
| 传感器类型： | 霍尔效应 |
| 电源电压： | 3 V ~ 5.5 V |
| 输出： | 2.5V |
| 频率： | 120kHz |
| 响应时间： | 4µs |
| 电极标记： | 双向 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SMD |
| 包装： | 标准包装 |
ACS716
120 kHz Bandwidth, High Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
COMMON OPERATING CHARACTERISTICS (continued) Valid at T A = –40°C to 125°C, V CC = 3.3 V, unless otherwise specified
Characteristic Symbol
Test Conditions
Min.
Typ.
Max.
Units
OVERCURRENT CHARACTERISTICS (continued)
Fault Enable (FAULT_EN Pin) Input High
Voltage Threshold
Fault Enable (FAULT_EN Pin) Input
Resistance
V IH
R FEI
0.8 × V CC
–
–
1
–
–
V
M Ω
Fault Enable (FAULT_EN Pin) Delay 7
t FED
Set FAULT_EN to low, V OC = 0.25 × V CC ,
C OC = 0 F; then run a DC I P exceeding the
corresponding overcurrent threshold; then
reset FAULT_EN from low to high and
–
15
–
μ s
measure the delay from the rising edge of
FAULT_EN to the falling edge of ˉFˉ ˉA ˉUˉˉLˉ ˉTˉ
Fault Enable (FAULT_EN Pin) Delay
(Non-Latching versions) 8
t FED(NL)
Set FAULT_EN to low, V OC = 0.25 × V CC ,
C OC = 0 F; then run a DC I P exceeding the
corresponding overcurrent threshold; then
reset FAULT_EN from low to high and
–
150
–
ns
measure the delay from the rising edge of
FAULT_EN to the falling edge of ˉFˉ ˉA ˉUˉˉLˉ ˉTˉ
FAULT_EN set to high for a minimum
of 20 μ s before the overcurrent event;
Overcurrent Fault Response Time
t OC
switchpoint set at V OC = 0.25 × V CC ;
apply a current step to I P with amplitude
equal to 1.5 x V OC / Sens;
delay from I P exceeding overcurrent
fault threshold to V ˉFˉ ˉA ˉUˉˉLˉ ˉTˉ < 0.4 V, without
external C OC capacitor
–
2
–
μ s
FAULT_EN set to high for a minimum
of 20 μ s before the undercurrent event;
Undercurrent Fault Response Time
(Non-Latching versions)
Overcurrent Fault Reset Delay
Overcurrent Fault Reset Hold Time
Overcurrent Input Pin Resistance
t UC
t OCR
t OCH
R OC
switchpoint set at V OC = 0.25 × V CC ; delay
from I P falling below the overcurrent fault
threshold to V ˉFˉ ˉA ˉUˉˉLˉ ˉTˉ > 0.8 × V CC , without
external C OC capacitor, R PU = 330 k Ω
Time from V FAULTEN < V IL to
V FAULT > 0.8 × V CC , R PU = 330 k Ω
Time from V FAULTEN pin < V IL to reset of
fault latch; see Functional Block Diagram
T A = 25°C, VOC pin to GND
–
–
–
2
3
500
250
–
–
–
–
–
μ s
ns
ns
M Ω
VOLTAGE REFERENCE CHARACTERISTIC S
Voltage Reference Output
Voltage Reference Output Load Current
Voltage Reference Output Drift
V ZCR
I ZCR
? V ZCR
T A = 25 °C
(Not a highly accurate reference)
Source current
Sink current
0.48 x V CC
3
50
–
0.5 × V CC
–
–
±10
0.52 x V CC
–
–
–
V
mA
μ A
mV
1 R F(INT) forms an RC circuit via the FILTER pin.
2 This parameter can drift by as much as 0.8% over
the lifetime of this product.
3 This
parameter can drift by as much as 1% over the lifetime of this product.
4 See page 8 on how to set overcurrent fault switchpoint.
5 Switchpoint can be lower at the expense of switchpoint accuracy.
6 This error specification does not include the effect of noise. See the I
fault switchpoint.
NCOMP specification in order to factor in the additional influence of noise on the
7 Fault Enable Delay is designed to avoid false tripping of an Overcurrent (OC) fault at power-up. A 15 μ s (typical) delay will always be needed, every
time FAULT_EN is raised from low to high, before the device is ready for responding to any overcurrent event.
8 During power-up, this delay is 15 μ s in order to avoid false tripping of an Overcurrent (OC) fault.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| ACS750SCA-050 | SENSOR CURRENT 50A 5V BI 5-CA |
| ACS756SCA-100B-PFF-T | IC HALL EFFECT SENSOR MOD 5PIN |
| ACS758KCB-150U-PFF-T | IC SENSOR CURRENT 150A UNI 3-CB |
| ACS759LCB-100B-PFF-T | SENSOR CURRENT |
| ADP1271 | SENSOR PRESSURE 490.3KPA STD DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ACS716KLATR-6BB-T | 功能描述:IC CURRENT SENSOR 120KHZ 16SOIC RoHS:是 类别:传感器，转换器 >> 电流 系列:- 标准包装:10 系列:* |
| ACS716KLATR-9BB-NL-T | 功能描述:Current Sensor 9A 1 Channel Hall Effect, Open Loop Bidirectional 16-SOIC (0.295", 7.50mm Width) 制造商:allegro microsystems, llc 系列:- 包装:带卷（TR） 零件状态:有效 用于测量:AC/DC 传感器类型:霍尔效应，开环 电流 - 检测:9A 通道数:1 输出:比率，电压 灵敏度:60mV/A 频率:DC ~ 120kHz 线性度:±0.25% 精度:±2.5% 电压 - 电源:3 V ~ 3.6 V 响应时间:4μs 电流 - 电源（最大值）:11mA 工作温度:-40°C ~ 125°C 极化:双向 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 标准包装:1,000 |
| ACS717KMATR-10B-T | 功能描述:Current Sensor 10A 1 Channel Hall Effect, Open Loop Bidirectional 16-SOIC (0.295", 7.50mm Width) 制造商:allegro microsystems, llc 系列:- 包装:剪切带（CT） 零件状态:有效 用于测量:AC/DC 传感器类型:霍尔效应，开环 电流 - 检测:10A 通道数:1 输出:比率，电压 灵敏度:132mV/A 频率:40kHz 线性度:±1% 精度:±2% 电压 - 电源:3 V ~ 3.6 V 响应时间:13μs 电流 - 电源（最大值）:7.5mA 工作温度:-40°C ~ 125°C 极化:双向 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 标准包装:1 |
| ACS717KMATR-20B-T | 功能描述:Current Sensor 20A 1 Channel Hall Effect, Open Loop Bidirectional 16-SOIC (0.295", 7.50mm Width) 制造商:allegro microsystems, llc 系列:- 包装:剪切带（CT） 零件状态:有效 用于测量:AC/DC 传感器类型:霍尔效应，开环 电流 - 检测:20A 通道数:1 输出:比率，电压 灵敏度:66mV/A 频率:40kHz 线性度:±1% 精度:±2% 电压 - 电源:3 V ~ 3.6 V 响应时间:13μs 电流 - 电源（最大值）:7.5mA 工作温度:-40°C ~ 125°C 极化:双向 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 标准包装:1 |
| ACS718KMATR-10B-T | 功能描述:Current Sensor 10A 1 Channel Hall Effect, Open Loop Bidirectional 16-SOIC (0.295", 7.50mm Width) 制造商:allegro microsystems, llc 系列:- 包装:剪切带（CT） 零件状态:有效 用于测量:AC/DC 传感器类型:霍尔效应，开环 电流 - 检测:10A 通道数:1 输出:比率，电压 灵敏度:200mv/A 频率:40kHz 线性度:±1% 精度:±2% 电压 - 电源:5V 响应时间:13μs 电流 - 电源（最大值）:9mA 工作温度:-40°C ~ 125°C 极化:双向 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。