参数资料
| 型号： | AD2S1205YSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC R/D 12BIT W/OSC 44-LQFP |
| 标准包装： | 1 |
| 类型： | R/D 转换器 |
| 分辨率（位）： | 12 b |
| 数据接口： | 串行，并联 |
| 电压电源： | 模拟和数字 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LQFP |
| 供应商设备封装： | 44-LQFP（7x7） |
| 包装： | 托盘 |
AD2S1205
Rev. A | Page 7 of 20
Pin No.
Mnemonic
Description
26
B
Incremental Encoder Emulation Output B. Logic output. This output is free running and is valid if the resolver format
input signals applied to the converter are valid.
27
NM
North Marker Incremental Encoder Emulation Output. Logic output. This output is free running and is valid if the
resolver format input signals applied to the converter are valid.
28
DIR
Direction. Logic output. This output is used in conjunction with the incremental encoder emulation outputs. The
DIR output indicates the direction of the input rotation and is high for increasing angular rotation.
29
DOS
Degradation of Signal. Logic output. Degradation of signal (DOS) is detected when either resolver input (Sin or Cos)
exceeds the specified DOS Sin/Cos threshold. See the Signal Degradation Detection section. DOS is indicated by a
logic low on the DOS pin and is not latched when the input signals exceed the maximum input level.
30
LOT
Loss of Tracking. Logic output. LOT is indicated by a logic low on the LOT pin and is not latched. See the Loss of
Signal Detection section.
31
FS1
Frequency Select 1. Logic input. FSI in conjunction with FS2 allows the frequency of EXC/EXC to be programmed.
32
FS2
Frequency Select 2. Logic input. FS2 in conjunction with FS1 allows the frequency of EXC/EXC to be programmed.
33
RESET
Reset. Logic input. The AD2S1205 requires an external reset signal to hold the RESET input low until VDD is within
the specified operating range of 4.5 V to 5.5 V. See the
section.
34
EXC
Excitiation Frequency. Analog output. An on-board oscillator provides the sinusoidal excitation signal (EXC) and its
complement signal (EXC) to the resolver. The frequency of this reference signal is programmable via the FS1 and FS2 pins.
35
EXC
Excitation Frequency Complement. Analog output. An on-board oscillator provides the sinusoidal excitation signal
(EXC) and its complement signal (EXC) to the resolver. The frequency of this reference signal is programmable via
the FS1 and FS2 pins.
36, 42
AGND
Analog Ground. These pins are ground reference points for analog circuitry on the AD2S1205. All analog input
signals and any external reference signal should be referred to this AGND voltage. Both of these pins should be
connected to the AGND plane of a system. The AGND and DGND voltages should ideally be at the same potential
and must not be more than 0.3 V apart, even on a transient basis.
37
Sin
Positive Analog Input of Differential Sin/SinLO Pair. The input range is 2.3 V p-p to 4.0 V p-p.
38
SinLO
Negative Analog Input of Differential Sin/SinLO Pair. The input range is 2.3 V p-p to 4.0 V p-p.
39
AVDD
Analog Supply Voltage, 4.75 V to 5.25 V. This pin is the supply voltage for all analog circuitry on the AD2S1205. The
AVDD and DVDD voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a
transient basis.
40
CosLO
Negative Analog Input of Differential Cos/CosLO Pair.
41
Cos
Positive Analog Input of Differential Cos/CosLO Pair.
43
REFBYP
Reference Bypass. Reference decoupling capacitors should be connected here. Typical recommended values are
10 μF and 0.01 μF.
44
REFOUT
Voltage Reference Output, 2.39 V to 2.52 V.
相关PDF资料 |
PDF描述 |
|---|---|
| AD2S1210ASTZ-RL7 | IC CONV R/D 10-16BIT OSC 48LQFP |
| AD2S44-UM18B | IC CONV SYNC/R-D 14BIT 2CH 32DIP |
| AD2S80AUD | IC R/D CONV TRACKING 40CDIP |
| AD2S83APZ-REEL | IC CONV R/D MONO VAR RES 44PLCC |
| AD2S90AP | IC R/D CONV 12BIT 20-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD2S1210 | 制造商:AD 制造商全称:Analog Devices 功能描述:Variable Resolution, 10-Bit to 16-Bit R/D Converter with Reference Oscillator |
| AD2S1210ASTZ | 功能描述:IC CONV R/D 10-16BIT 48-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD2S1210ASTZ-RL7 | 功能描述:IC CONV R/D 10-16BIT OSC 48LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD2S1210BSTZ | 功能描述:IC CONV R/D 10-16BIT 48-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD2S1210BSTZ-DASSAULT | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。