- 您现在的位置：买卖IC网 > PDF目录11657 > AD2S81AJD (Analog Devices Inc)IC R/D CONV TRACKING 28CDIP PDF资料下载
参数资料
| 型号： | AD2S81AJD |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/20页 |
| 文件大小： | 0K |
| 描述： | IC R/D CONV TRACKING 28CDIP |
| 标准包装： | 1 |
| 类型： | R/D 转换器 |
| 输入类型： | 并联 |
| 输出类型： | 数字 |
| 接口： | 并联 |
| 电流 - 电源： | 30mA |
| 安装类型： | 通孔 |
| 封装/外壳： | 28-CDIP（0.605"，15.37mm） |
| 供应商设备封装： | 28-CDIP |
| 包装： | 管件 |
AD2S80A
REV. B
–10–
CIRCUIT FUNCTIONS AND DYNAMIC PERFORMANCE
The AD2S80A allows the user greater flexibility in choosing the
dynamic characteristics of the resolver-to-digital conversion to
ensure the optimum system performance. The characteristics
are set by the external components shown in Figure 1, and the
section “COMPONENT SELECTION” explains how to select
desired maximum tracking rate and bandwidth values. The
following paragraphs explain in greater detail the circuit of the
AD2S80A and the variations in the dynamic performance avail-
able to the user.
Loop Compensation
The AD2S80A (connected as shown in Figure 1) operates as a
Type 2 tracking servo loop where the VCO/counter combination
and Integrator perform the two integration functions inherent in
a Type 2 loop.
Additional compensation in the form of a pole/zero pair is
required to stabilize any Type 2 loop to avoid the loop gain
characteristic crossing the 0 dB axis with 180
° of additional
phase lag, as shown in Figure 5.
This compensation is implemented by the integrator compo-
nents (R4, C4, R5, C5).
The overall response of such a system is that of a unity gain
second order low pass filter, with the angle of the resolver as the
input and the digital position data as the output.
The AD2S80A does not have to be connected as tracking con-
verter, parts of the circuit can be used independently. This is
particularly true of the Ratio Multiplier which can be used as a
control transformer (see Application Note).
A block diagram of the AD2S80A is given in Figure 3.
Ratio Multiplier
The ratio multiplier is the input section of the AD2S80A and
compares the signal from the resolver input angle,
θ, to the
digital angle,
φ, held in the counter. Any difference between
these two angles results in an analog voltage at the AC ERROR
OUTPUT. This circuit function has historically been called
a “Control Transformer” as it was originally performed by an
electromechanical device known by that name.
The AC ERROR signal is given by
A1 sin (
θ–φ) sin
ωt
where
ω = 2 π fREF
fREF = reference frequency
A1, the gain of the ratio multiplier stage is 14.5.
So for 2 V rms inputs signals
AC ERROR output in volts/(bit of error)
= 2 × sin
360
n
× A1
where n = bits per rev
= 1,024 for 10 bits resolution
= 4,096 for 12 bits
= 16,384 for 14 bits
= 65,536 for 16 bits
giving an AC ERROR output
= 178 mV/bit @ 10 bits resolution
= 44.5 mV/bit @ 12 bits
= 11.125 mV/bit @ 14 bits
= 2.78 mV/bit @ 16 bits
The ratio multiplier will work in exactly the same way whether
the AD2S80A is connected as a tracking converter or as a con-
trol transformer, where data is preset into the counters using the
DATA LOAD pin.
HF Filter
The AC ERROR OUTPUT may be fed to the PSD via a simple
ac coupling network (R2, C1) to remove any dc offset at this
point. Note, however, that the PSD of the AD2S80A is a wide-
band demodulator and is capable of aliasing HF noise down to
within the loop bandwidth. This is most likely to happen where
the resolver is situated in particularly noisy environments, and
the user is advised to fit a simple HF filter R1, C2 prior to the
phase sensitive demodulator.
The attenuation and frequency response of a filter will affect the
loop gain and must be taken into account in deriving the loop
transfer function. The suggested filter (R1, C1, R2, C2) is
shown in Figure 1 and gives an attenuation at the reference
frequency (fREF) of 3 times at the input to the phase sensitive
demodulator .
Values of components used in the filter must be chosen to ensure
that the phase shift at fREF is within the allowable signal to
reference phase shift of the converter.
Phase Sensitive Demodulator
The phase sensitive demodulator is effectively ideal and devel-
ops a mean dc output at the DEMODULATOR OUTPUT
pin of
±22
π
× (DEMODULATOR INPUT rms voltage )
PHASE
SENSITIVE
DEMODULATOR
A1 sin ( – ) sin t
AC ERROR
sin
t
cos
sin
t
DIGITAL
VCO
R5
R6
C5
C4
R4
INTEGRATOR
VELOCITY
CLOCK
DIRECTION
RATIO
MULTIPLIER
Figure 3. Functional Diagram
C
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JNM-IY-F2 | CONVERTER MOD DC/DC 10V 50W |
| 413589-3 | CONN PLUG BNC BELDEN 8218 CRIMP |
| AD2S83IPZ | IC CONV R/D MONO VAR RES 44PLCC |
| VE-JNM-IY-F1 | CONVERTER MOD DC/DC 10V 50W |
| AD2S83IPZ-REEL | IC CONV R/D MONO VAR RES 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD2S82 | 制造商:AD 制造商全称:Analog Devices 功能描述:Variable Resolution, Monolithic Resolver-to-Digital Converters |
| AD2S82A | 制造商:AD 制造商全称:Analog Devices 功能描述:Variable Resolution, Monolithic Resolver-to-Digital Converters |
| AD2S82AHP | 功能描述:IC R/D CONV TRACKING 44PLCC RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
| AD2S82AHP | 制造商:Analog Devices 功能描述:IC R/D CONVERTER. 2S82 |
| AD2S82AHP-REEL | 功能描述:IC CONV R/D MONO VAR RES 44PLCC RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。