- 您现在的位置：买卖IC网 > PDF目录8984 > AD5061YRJZ-1500RL7 (Analog Devices Inc)IC DAC 16BIT SPI/SRL SOT23-8 PDF资料下载
参数资料
| 型号： | AD5061YRJZ-1500RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT SPI/SRL SOT23-8 |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 1 |
| 系列： | nanoDAC™ |
| 设置时间： | 4µs |
| 位数： | 16 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 |
| 供应商设备封装： | SOT-23-8 |
| 包装： | 标准包装 |
| 输出数目和类型： | 1 电压，单极；1 电压，双极 |
| 采样率（每秒）： | 1.3M |
| 其它名称： | AD5061YRJZ-1500RL7DKR |
AD5061
Rev. B | Page 19 of 20
USING A GALVANICALLY-ISOLATED INTERFACE
CHIP
In process control applications in industrial environments, it is
often necessary to use a galvanically-isolated interface to protect
and isolate the controlling circuitry from any hazardous
common-mode voltages that may occur in the area where the
DAC is functioning. iCoupler
provides isolation in excess of
2.5 kV. Because the AD5061 uses a 3-wire serial logic interface,
the ADuM130x family provides an ideal digital solution for the
DAC interface.
The ADuM130x isolators provide three independent isolation
channels in a variety of channel configurations and data rates.
They operate across the full range from 2.7 V to 5.5 V, providing
compatibility with lower voltage systems and enabling a voltage
translation functionality across the isolation barrier.
Figure 48 shows a typical galvanically-isolated configuration
using the AD5061. The power supply to the part also needs to
be isolated; this is accomplished by using a transformer. On the
DAC side of the transformer, a 5 V regulator provides the 5 V
supply required for the AD5061.
0.1F
10F
VDD
GND
POWER
5V
REGULATOR
AD5061
04
76
2-
03
8
ADuM130x
SCLK
V0A
V1A
SCLK
VOUT
SYNC
V0B
V1B
SDI
DIN
V0C
V1C
DATA
Figure 48. AD5061 with a Galvanically-Isolated Interface
POWER SUPPLY BYPASSING AND GROUNDING
When accuracy is important in a circuit, it is helpful to carefully
consider the power supply and ground return layout on the
board. The printed circuit board containing the AD5061 should
have separate analog and digital sections, each having its own
area of the board. If the AD5061 is in a system where other
devices require an AGND-to-DGND connection, then the
connection should be made at one point only. This ground
point should be as close as possible to the AD5061.
The power supply to the AD5061 should be bypassed with
10 μF and 0.1 μF capacitors. The capacitors should be physically
as close as possible to the device with the 0.1 μF capacitor
ideally right up against the device. The 10 μF capacitors are the
tantalum bead type. It is important that the 0.1 μF capacitor has
low effective series resistance (ESR) and effective series
inductance (ESI), as do common ceramic types of capacitors.
This 0.1 μF capacitor provides a low impedance path to ground
for high frequencies caused by transient currents due to internal
logic switching.
The power supply line itself should have as large a trace as
possible to provide a low impedance path and reduce glitch
effects on the supply line. Clocks and other fast switching
digital signals should be shielded from other parts of the board
by digital ground. Avoid crossover of digital and analog signals,
if possible. When traces cross on opposite sides of the board,
ensure that they run at right angles to each other to reduce
feedthrough effects through the board. The best board layout
technique is the microstrip technique where the component
side of the board is dedicated to the ground plane only, and the
signal traces are placed on the solder side. However, this is not
always possible with a 2-layer board.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-261-MW-F1 | CONVERTER MOD DC/DC 12V 100W |
| VE-J00-MZ-F3 | CONVERTER MOD DC/DC 5V 25W |
| VE-J00-MZ-F2 | CONVERTER MOD DC/DC 5V 25W |
| VE-J00-MZ-F1 | CONVERTER MOD DC/DC 5V 25W |
| VE-24Z-MU-F3 | CONVERTER MOD DC/DC 2V 80W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5061YRJZ-1REEL7 | 功能描述:IC DAC 16BIT SPI/SRL SOT23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:nanoDAC™ 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5062 | 制造商:AD 制造商全称:Analog Devices 功能描述:Full Accurate 16 Bit Vout nanoDac, 2.7V- 5.5V, in a Sot 23 |
| AD50621 | 制造商:AD 制造商全称:Analog Devices 功能描述:Fully Accurate, 16-Bit, Unbuffered VOUT, Quad SPI Interface, 2.7 V to 5.5 V nanoDAC in a TSSOP |
| AD5062ARJZ-1 | 制造商:Analog Devices 功能描述:DAC 1CH R-2R 16BIT 8PIN SOT-23 - Bulk |
| AD5062ARJZ-1500RL7 | 功能描述:IC DAC 16BIT 2.7-5.5V SOT23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:nanoDAC™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。