- 您现在的位置：买卖IC网 > PDF目录8981 > AD5062BRJZ-2500RL7 (Analog Devices Inc)IC DAC 16BIT 2.7-5.5V SOT23-8 PDF资料下载
参数资料
| 型号： | AD5062BRJZ-2500RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT 2.7-5.5V SOT23-8 |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 1 |
| 系列： | nanoDAC™ |
| 设置时间： | 4µs |
| 位数： | 16 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 |
| 供应商设备封装： | SOT-23-8 |
| 包装： | 标准包装 |
| 输出数目和类型： | 1 电压，单极；1 电压，双极 |
| 采样率（每秒）： | 1.3M |
| 其它名称： | AD5062BRJZ-2500RL7DKR |
AD5062
Rev. A | Page 14 of 20
THEORY OF OPERATION
The AD5062 is a single 16-bit, serial input, voltage output DAC.
It operates from supply voltages of 2.7 V to 5.5 V. Data is
written to the AD5062 in a 24-bit word format, via a 3-wire
serial interface.
The AD5062 incorporates a power-on reset circuit that ensures
the DAC output powers up to zero-scale or midscale. The
device also has a software power-down mode pin that reduces
the typical current consumption to less than 1 μA.
DAC ARCHITECTURE
The DAC architecture of the AD5062 consists of two matched
DAC sections. A simplified circuit diagram is shown in
Figure 33. The four MSBs of the 16-bit data-word are decoded
to drive 15 switches, E1 to E15. Each of these switches connects
one of 15 matched resistors to either DACGND or VREF
buffer
output. The remaining 12 bits of the data-word drive switches
S0 to S11 of a 12-bit voltage mode R-2R ladder network.
2R
047766-
027
S0
VREF
2R
S1
2R
S11
2R
E1
2R
E2
2R
E15
2R
VOUT
12-BIT R-2R LADDER
FOUR MSBs DECODED INTO
15 EQUAL SEGMENTS
Figure 33. DAC Ladder Structure
REFERENCE BUFFER
The AD5062 operates with an external reference. The reference
input (VREF) has an input range of 2 V to VDD 50 mV. This
input voltage is then used to provide a buffered reference for the
DAC core.
SERIAL INTERFACE
The AD5062 has a 3-wire serial interface (SYNC, SCLK, and
DIN), which is compatible with SPI, QSPI, and MICROWIRE
interface standards, as well as most DSPs. See
for a
timing diagram of a typical write sequence.
The write sequence begins by bringing the SYNC line low. Data
from the DIN line is clocked into the 24-bit shift register on the
falling edge of SCLK. The serial clock frequency can be as high
as 30 MHz, making these parts compatible with high speed
DSPs. On the 24th falling clock edge, the last data bit is clocked
in and the programmed function is executed (that is, a change
in the DAC register contents and/or a change in the mode of
operation).
At this stage, the SYNC line may be kept low or be brought
high. In either case, it must be brought high for a minimum of
33 ns before the next write sequence so that a falling edge of
SYNC can initiate the next write sequence. Because the SYNC
buffer draws more current when VIN = 1.8 V than it does when
VIN = 0.8 V, SYNC should be idled low between write sequences
for even lower power operation of the part. As previously indi-
cated, however, it must be brought high again just before the
next write sequence.
INPUT SHIFT REGISTER
The input shift register is 24 bits wide; see Figure 34. PD1 and
PD0 are control bits that control which mode of operation the
part is in (normal mode or any one of three power-down
modes). There is a more complete description of the various
modes in the Power-Down Modes section. The next 16 bits are
the data bits. These are transferred to the DAC register on the
24th falling edge of SCLK.
SYNC INTERRUPT
In a normal write sequence, the SYNC line is kept low for at
least 24 falling edges of SCLK and the DAC is updated on the
24th falling edge. However, if SYNC is brought high before the
24th falling edge, this acts as an interrupt to the write sequence.
The shift register is reset and the write sequence is seen as
invalid. Neither an update of the DAC register contents nor a
change in the operating mode occurs; see
.
DATA BITS
DB15 (MSB)
DB0 (LSB)
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
NORMAL OPERATION
1k
Ω TO GND
100k
Ω TO GND
3-STATE
POWER-DOWN MODES
0
1
0
1
0
1
04766-
028
0
PD1
PD0
Figure 34. Input Register Contents
相关PDF资料 |
PDF描述 |
|---|---|
| ICS843023AGILFT | IC CLK GENERATOR LVPECL 8-TSSOP |
| AD5063BRMZ | IC DAC 16BIT 2.7-5.5V 10-MSOP |
| AD5063BRMZ-1 | IC DAC 16BIT 2.7-5.5V 10MSOP |
| VE-J0P-MZ-F4 | CONVERTER MOD DC/DC 13.8V 25W |
| VI-B0T-MY-F2 | CONVERTER MOD DC/DC 6.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5062BRJZ-2REEL7 | 功能描述:IC DAC 16BIT 2.7-5.5V SOT23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:nanoDAC™ 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| AD5063 | 制造商:AD 制造商全称:Analog Devices 功能描述:Full Accurate 14/16 Bit Vout nanoDac Buffered, 3V/5V, Sot 23 |
| AD5063_09 | 制造商:AD 制造商全称:Analog Devices 功能描述:Fully Accurate 16-Bit VOUT nanoDAC SPI Interface 2.7 V to 5.5 V in an MSOP |
| AD50631 | 制造商:AD 制造商全称:Analog Devices 功能描述:Fully Accurate, 16-Bit, Unbuffered VOUT, Quad SPI Interface, 2.7 V to 5.5 V nanoDAC in a TSSOP |
| AD5063BRM-1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Full Accurate 16 Bit Vout nanoDac, 2.7V- 5.5V, in a Sot 23 |
发布紧急采购，3分钟左右您将得到回复。