- 您现在的位置：买卖IC网 > PDF目录9281 > AD5235BRUZ250-R7 (Analog Devices Inc)IC DGTL POT DUAL 1024POS 16TSSOP PDF资料下载
参数资料
| 型号： | AD5235BRUZ250-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/32页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT DUAL 1024POS 16TSSOP |
| 产品变化通告： | Metal Edit Change 03/Feb/2012 |
| 标准包装： | 1,000 |
| 接片： | 1024 |
| 电阻（欧姆）： | 250k |
| 电路数： | 2 |
| 温度系数： | 标准值 35 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 3 V ~ 5.5 V，±2.25 V ~ 2.75 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD5235
Data Sheet
Rev. F | Page 16 of 32
THEORY OF OPERATION
The AD5235 digital potentiometer is designed to operate as a
true variable resistor. The resistor wiper position is determined
by the RDAC register contents. The RDAC register acts as a
scratchpad register, allowing unlimited changes of resistance
settings. The scratchpad register can be programmed with any
position setting using the standard SPI serial interface by loading
the 24-bit data-word. In the format of the data-word, the first four
bits are commands, the following four bits are addresses, and the
last 16 bits are data. When a specified value is set, this value can
be stored in a corresponding EEMEM register. During subsequent
power-ups, the wiper setting is automatically loaded to that value.
Storing data to the EEMEM register takes about 15 ms and
consumes approximately 2 mA. During this time, the shift
register is locked, preventing any changes from taking place.
The RDY pin pulses low to indicate the completion of this
EEMEM storage. There are also 13 addresses with two bytes
each of user-defined data that can be stored in the EEMEM
register from Address 2 to Address 14.
The following instructions facilitate the programming needs
of the user (see Table 7 for details):
0. Do nothing.
1. Restore EEMEM content to RDAC.
2. Store RDAC setting to EEMEM.
3. Store RDAC setting or user data to EEMEM.
4. Decrement by 6 dB.
5. Decrement all by 6 dB.
6. Decrement by one step.
7. Decrement all by one step.
8. Reset EEMEM content to RDAC.
9. Read EEMEM content from SDO.
10. Read RDAC wiper setting from SDO.
11. Write data to RDAC.
12. Increment by 6 dB.
13. Increment all by 6 dB.
14. Increment by one step.
15. Increment all by one step.
Table 14 to Table 20 provide programming examples that use
some of these commands.
SCRATCHPAD AND EEMEM PROGRAMMING
The scratchpad RDAC register directly controls the position of
the digital potentiometer wiper. For example, when the scratchpad
register is loaded with all 0s, the wiper is connected to Terminal B
of the variable resistor. The scratchpad register is a standard
logic register with no restriction on the number of changes
allowed, but the EEMEM registers have a program erase/write
cycle limitation.
BASIC OPERATION
The basic mode of setting the variable resistor wiper position
(programming the scratchpad register) is accomplished by
loading the serial data input register with Instruction 11 (0xB),
Address 0, and the desired wiper position data. When the proper
wiper position is determined, the user can load the serial data
input register with Instruction 2 (0x2), which stores the wiper
position data in the EEMEM register. After 15 ms, the wiper
position is permanently stored in nonvolatile memory.
Table 5 provides a programming example listing the sequence
of the serial data input (SDI) words with the serial data output
appearing at the SDO pin in hexadecimal format.
Table 5. Write and Store RDAC Settings to EEMEM Registers
SDI
SDO
Action
0xB00100
0xXXXXXX
Writes data 0x100 to the RDAC1 register,
Wiper W1 moves to 1/4 full-scale position.
0x20XXXX
0xB00100
Stores RDAC1 register content into the
EEMEM1 register.
0xB10200
0x20XXXX
Writes Data 0x200 to the RDAC2 register,
Wiper W2 moves to 1/2 full-scale position.
0x21XXXX
0xB10200
Stores RDAC2 register contents into the
EEMEM2 register.
At system power-on, the scratchpad register is automatically
refreshed with the value previously stored in the corresponding
EEMEM register. The factory-preset EEMEM value is midscale.
The scratchpad register can also be refreshed with the contents
of the EEMEM register in three different ways. First, executing
Instruction 1 (0x1) restores the corresponding EEMEM value.
Second, executing Instruction 8 (0x8) resets the EEMEM values
of both channels. Finally, pulsing the PR pin refreshes both
EEMEM settings. Operating the hardware control PR function
requires a complete pulse signal. When PR goes low, the internal
logic sets the wiper at midscale. The EEMEM value is not
loaded until PR returns high.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1135Z-8+T&R | IC DELAY LINE 8NS 8-SOIC |
| AD5235BRUZ25-RL7 | IC DGTL POT DUAL 1024POS 16TSSOP |
| VI-2TP-MW | CONVERTER MOD DC/DC 13.8V 100W |
| DS1135Z-12+T&R | IC DELAY LINE 12NS 8-SOIC |
| DS1135Z-20+T&R | IC DELAY LINE 20NS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5235BRUZ25-EP-R7 | 功能描述:IC DGTL POT 1024POS DUAL 16TSSOP 制造商:analog devices inc. 系列:* 零件状态:在售 标准包装:1,000 |
| AD5235BRUZ25-RL7 | 功能描述:IC DGTL POT DUAL 1024POS 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5235-EP | 制造商:AD 制造商全称:Analog Devices 功能描述:Nonvolatile Memory, Dual 1024-Position Digital Potentiometer |
| AD5235EVAL | 制造商:Analog Devices 功能描述:DUAL 10BIT SPI EVAL BOARD - Bulk |
| AD5235EVAL25 | 制造商:Analog Devices 功能描述:Evaluation Board For 1024-Position Digital Potentiometer 制造商:Analog Devices 功能描述:DUAL 10BIT SPI EVAL BOARD - Bulk |
发布紧急采购，3分钟左右您将得到回复。