参数资料
| 型号： | AD524BE |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC AMP INST 1MHZ PREC LN 20CLCC |
| 标准包装： | 1 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 转换速率： | 5 V/µs |
| 增益带宽积： | 1MHz |
| -3db带宽： | 1MHz |
| 电流 - 输入偏压： | 25nA |
| 电压 - 输入偏移： | 100µV |
| 电流 - 电源： | 3.5mA |
| 电压 - 电源，单路/双路(±)： | ±6 V ~ 18 V |
| 工作温度： | -25°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-CLCC |
| 供应商设备封装： | 20-LCCC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD524
Rev. F | Page 16 of 28
Voltage offset and drift comprise two components each; input
and output offset and offset drift. Input offset is the component
of offset that is directly proportional to gain, that is, input offset
as measured at the output at G = 100 is 100 times greater than at
G = 1. Output offset is independent of gain. At low gains, output
offset drift is dominant, at high gains, input offset drift dominates.
Therefore, the output offset voltage drift is normally specified as
drift at G = 1 (where input effects are insignificant), whereas
input offset voltage drift is given by drift specification at a high
gain (where output offset effects are negligible). All input
related numbers are referred to the input (RTI) that is the effect
on the output is G times larger. Voltage offset vs. power supply
is also specified at one or more gain settings and is also RTI.
By separating these errors, one can evaluate the total error
independent of the gain setting used. In a given gain configura-
tion, both errors can be combined to give a total error referred
to the input (RTI) or output (RTO) by the following formulas:
Total error RTI = input error + (output error/gain)
Total error RTO = (gain × input error) + output error
As an illustration, a typical AD524 might have a +250 μV
output offset and a 50 μV input offset. In a unity gain
configuration, the total output offset would be 200 μV or
the sum of the two. At a gain of 100, the output offset would
be 4.75 mV or: +250 μV + 100(50 μV) = 4.75 mV.
The AD524 provides for both input and output offset adjustment.
This simplifies very high precision applications and minimizes
offset voltage changes in switched gain applications. In such
applications, the input offset is adjusted first at the highest
programmed gain, then the output offset is adjusted at G = 1.
GAIN
The AD524 has internal high accuracy pretrimmed resistors
for pin programmable gains of 1, 10, 100, and 1000. One of the
preset gains can be selected by pin strapping the appropriate
gain terminal and RG2 together (for G = 1, RG2 is not connected).
AD524
G = 10
G = 100
G = 1000
+INPUT
–INPUT
VOUT
OUTPUT
SIGNAL
COMMON
–VS
INPUT
OFFSET
NULL
+VS
10k
RG1
RG2
1
16
13
12
11
3
2
8
4
5
10
9
6
7
005
00-
034
Figure 34. Operating Connections for G = 100
The AD524 can be configured for gains other than those that
are internally preset; there are two methods to do this. The first
method uses just an external resistor connected between
Pin 3 and Pin 16 (see Figure 35), which programs the gain
according to the following formula:
1
k
40
=
Ω
=
G
R
G
For best results, RG should be a precision resistor with a low
temperature coefficient. An external RG affects both gain
accuracy and gain drift due to the mismatch between it and
the internal thin-film resistors. Gain accuracy is determined
by the tolerance of the external RG and the absolute accuracy
of the internal resistors (±20%). Gain drift is determined by the
mismatch of the temperature coefficient of RG and the tempera-
ture coefficient of the internal resistors (50 ppm/°C typical).
40,000
2.105
G =
+ 1 = 20 ±20%
AD524
REFERENCE
1k
+INPUT
–INPUT
2.105k
1.5k
VOUT
+VS
–VS
RG1
RG2
1
16
8
7
6
9
10
13
12
11
3
2
00500
-03
5
Figure 35. Operating Connections for G = 20
The second method uses the internal resistors in parallel with
an external resistor (see Figure 36). This technique minimizes
the gain adjustment range and reduces the effects of tempera-
ture coefficient sensitivity.
G =
G = 10
AD524
REFERENCE
+INPUT
–INPUT
4k
*R|G = 10 = 4444.44
*R|G = 100 = 404.04
*R|G = 1000 = 40.04
*NOMINAL (±20%)
VOUT
40,000
4000||4444.44
+ 1 = 20 ±17%
+VS
–VS
RG1
RG2
1
16
13
12
11
3
2
8
7
10
6
9
00500
-03
6
Figure 36. Operating Connections for G = 20, Low Gain
Temperature Coefficient Technique
相关PDF资料 |
PDF描述 |
|---|---|
| 3408-5003 | CONN HEADER 16POS R/A NO LATCH |
| AD204JN | IC AMP ISOL 5KHZ QUAD LP 38DIP |
| 3314-6303 | CONN HEADER 14POS STR LONG LATCH |
| AD204JY | IC AMP ISOL 5KHZ QUAD LP 38SIP |
| 350015-2 | CONN RECEPT 18-22 AWG .093 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD524C | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Instrumentation Amplifier |
| AD524CD | 功能描述:IC AMP INST 1MHZ PREC LN 16CDIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:TS1854A View All Specifications 标准包装:50 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.25 V/µs 增益带宽积:630kHz -3db带宽:- 电流 - 输入偏压:16nA 电压 - 输入偏移:1000µV 电流 - 电源:162µA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):1.8 V ~ 6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 |
| AD524CD/+ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Instrumentation Amp， Pin-Programmable |
| AD524CDZ | 功能描述:IC AMP INST 1MHZ PREC LN 16CDIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD524CE | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。