参数资料
| 型号： | AD5254BRUZ1 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/32页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT QUAD 1K I2C 20-TSSOP |
| 标准包装： | 75 |
| 接片： | 256 |
| 电阻（欧姆）： | 1k |
| 电路数： | 4 |
| 温度系数： | 标准值 650 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V，±2.25 V ~ 2.75 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 787 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD5253/AD5254
Data Sheet
Rev. C | Page 16 of 32
RDAC/EEMEM Write
Setting the wiper position requires an RDAC write operation.
The single write operation is shown in Figure 27, and the
consecutive write operation is shown in Figure 28. In the
consecutive write operation, if the RDAC is selected and the
address starts at 0, the first data byte goes to RDAC0, the second
data byte goes to RDAC1, the third data byte goes to RDAC2,
and the fourth data byte goes to RDAC3. This operation can be
continued for up to eight addresses with four unused addresses;
it then loops back to RDAC0. If the address starts at any of the
eight valid addresses, N, the data first goes to RDAC_N,
RDAC_N + 1, and so on; it loops back to RDAC0 after the
eighth address. The RDAC address is shown in Table 6.
While the RDAC wiper setting is controlled by a specific
RDAC register, each RDAC register corresponds to a specific
EEMEM location, which provides nonvolatile wiper storage
functionality. The addresses are shown in Table 7. The single
and consecutive write operations also apply to EEMEM write
operations.
There are 12 nonvolatile memory locations: EEMEM4 to
EEMEM15. Users can store 12 bytes of information, such as
memory data for other components, look-up tables, or system
identification information.
In a write operation to the EEMEM registers, the device disables
the I2C interface during the internal write cycle. Acknowledge
polling is required to determine the completion of the write
cycle. See the EEMEM Write-Acknowledge Polling section.
RDAC/EEMEM Read
The AD5253/AD5254 provide two different RDAC or EEMEM
read operations. For example, Figure 29 shows the method of
reading the RDAC0 to RDAC3 contents without specifying the
address, assuming Address RDAC0 was already selected in the
previous operation. If an RDAC_N address other than RDAC0
was previously selected, readback starts with Address N,
followed by N + 1, and so on.
Figure 30 illustrates a random RDAC or EEMEM read
operation. This operation allows users to specify which RDAC
or EEMEM register is read by issuing a dummy write command
to change the RDAC address pointer and then proceeding with
the RDAC read operation at the new address location.
Table 7. Addresses for Writing (Storing) RDAC Settings and
User-Defined Data to EEMEM Registers
(R/W = 0, CMD/REG = 0, EE/RDAC = 1)
A4
A3
A2
A1
A0
Data Byte Description
0
Store RDAC0 setting to EEMEM01
0
1
Store RDAC1 setting to EEMEM11
0
1
0
Store RDAC2 setting to EEMEM21
0
1
Store RDAC3 setting to EEMEM31
0
1
0
Store user data to EEMEM4
0
1
0
1
Store user data to EEMEM5
0
1
0
Store user data to EEMEM6
0
1
Store user data to EEMEM7
0
1
0
Store user data to EEMEM8
0
1
0
1
Store user data to EEMEM9
0
1
0
1
0
Store user data to EEMEM10
0
1
0
1
Store user data to EEMEM11
0
1
0
Store user data to EEMEM12
0
1
0
1
Store user data to EEMEM13
0
1
0
Store user data to EEMEM14
0
1
Store user data to EEMEM15
Table 8. Addresses for Reading (Restoring) RDAC Settings
and User Data from EEMEM
(R/W = 1, CMD/REG = 0, EE/RDAC = 1)
A4
A3
A2
A1
A0
Data Byte Description
0
Read RDAC0 setting from EEMEM0
0
1
Read RDAC1 setting from EEMEM1
0
1
0
Read RDAC2 setting from EEMEM2
0
1
Read RDAC3 setting from EEMEM3
0
1
0
Read User data from EEMEM4
0
1
0
1
Read user data from EEMEM5
0
1
0
Read user data from EEMEM6
0
1
Read user data from EEMEM7
0
1
0
Read user data from EEMEM8
0
1
0
1
Read user data from EEMEM9
0
1
0
1
0
Read user data from EEMEM10
0
1
0
1
Read user data from EEMEM11
0
1
0
Read user data from EEMEM12
0
1
0
1
Read user data from EEMEM13
0
1
0
Read user data from EEMEM14
0
1
Read user data from EEMEM15
1 Users can store any of the 64 RDAC settings for AD5253 or any of the 256
RDAC settings for the AD5254 directly to the EEMEM. This is not limited to
current RDAC wiper setting.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5254BRUZ10 | IC POT DGTL QUAD 10K I2C 20TSSOP |
| IDT74CBTLV3244PGG8 | IC BUS SWITCH OCTAL LV 20-TSSOP |
| AD5263BRUZ200 | IC POT QUAD 200K 256POS 24-TSSOP |
| AD5263BRUZ20 | IC DGTL POT QUAD 20K 24-TSSOP |
| AD5233BRUZ50 | IC POT QUAD 50K 64POS 24-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5254BRUZ10 | 功能描述:IC POT DGTL QUAD 10K I2C 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5254BRUZ100 | 功能描述:IC POT DGTL QUAD 100K 20-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5254BRUZ100-RL7 | 功能描述:IC DGTL POT 256POS 100K 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5254BRUZ10-RL7 | 功能描述:IC POT DGTL QUAD 10K I2C 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5254BRUZ1-RL7 | 功能描述:IC DGTL POT QUAD 1K 20-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。