- 您现在的位置：买卖IC网 > PDF目录373875 > AD5280BRU200 (ANALOG DEVICES INC) 32-Tap. Nonvolatile. Linear-Taper Digital Potentiometers in SOT23 PDF资料下载
参数资料
| 型号： | AD5280BRU200 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 数字电位计 |
| 英文描述： | 32-Tap. Nonvolatile. Linear-Taper Digital Potentiometers in SOT23 |
| 中文描述： | 200K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO14 |
| 封装： | MO-153AB-1, TSSOP-14 |
| 文件页数： | 7/10页 |
| 文件大小： | 156K |
| 代理商： | AD5280BRU200 |
PRELIMINARY TECHNICAL DATA
AD5280/AD5282
REV PrE 12 MAR 02
Information contained in this Product Concept Data Sheet describes a product in the early definition stage. There is no guarantee that the information contained here will become a final
product in its present form. For latest information contact Walt Heinzer/Analog Devices, Santa Clara, CA. TEL 408 382-3107; FAX 408 382-2721; email; walt.heinzer@analog.com
7
For example, R
AB
=20K
, when V
A
= 0V and B–terminal is open
circuit, the following output resistance R
WA
will be set for the
following RDAC latch codes. Result will be the same if terminal
B is tied to W:
D
(DEC)
R
WA
(
)
Output State
256
128
1
0
60
10060
19982
20060
Full-Scale
Mid-Scale
1 LSB
Zero-Scale
The typical distribution of the nominal resistance R
AB
from
channel-to-channel matches within ±1%. Device to device
matching is process lot dependent and is possible to have ±30%
variation. Since the resistance element is processed in thin film
technology, the change in R
AB
with temperature has a
30
ppm/°C temperature coefficient.
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer easily generates output voltages at
wiper-to-B and wiper-to-A to be proportional to the input
voltage at A-to-B. Let’s ignore the effect of the wiper resistance
at the moment. For example connecting A–terminal to +5V and
B–terminal to ground produces an output voltage at the wiper-
to-B starting at zero volts up to 1 LSB less than +5V. Each LSB
of voltage is equal to the voltage applied across terminal AB
divided by the 256 position of the potentiometer divider. Since
AD5280/AD5282 can be supplied by dual supplies, the general
equation defining the output voltage at V
W
with respect to
ground for any given input voltage applied to terminals AB is:
3
eqn.
256
256
256
)
(
B
A
W
V
D
V
D
D
V
+
=
where D is decimal equivalent of the binary code which is
loaded in the 8-bit RDAC register.
Operation of the digital potentiometer in the divider mode
results in a more accurate operation over temperature. Unlike
the rheostat mode, the output voltage is dependent on the ratio
of the internal resistors R
WA
and R
WB
and not the absolute values,
therefore, the temperature drift reduces to
5
ppm/°C.
DIGITAL INTERFACE
2-WIRE SERIAL BUS
The AD5280/AD5282 are controlled via an I
2
C compatible
serial bus. The RDACs are connected to this bus as slave
devices.
Referring from Figures 2 and 3, the first byte of
AD5280/AD5282 is a Slave Address Byte. It has a 7-bit slave
address and a R/
W
bit. The 5 MSBs are 01011 and the following
2 bits are determined by the state of the AD0 and AD1 pins of
the device. AD0 and AD1 allow the user to use up to four of
these devices on one bus.
The 2-wire I
2
C serial bus protocol operates as follows:
1.
The master initiates data transfer by establishing a START
condition, which is when a high-to-low transition on the
SDA line occurs while SCL is high, Figure 2. The
following byte is the Slave Address Byte which consists of
the 7-bit slave address followed by an R/
W
bit (this bit
determines whether data will be read from or written to the
slave device).
The slave whose address corresponds to the transmitted
address responds by pulling the SDA line low during the
ninth clock pulse (this is termed the Acknowledge bit). At
this stage, all other devices on the bus remain idle while the
selected device waits for data to be written to or read from
its serial register. If the R/
W
bit is high, the master will read
from the slave device. On the other hand, if the R/
W
bit is
low, the master will write to the slave device.
2.
A Write operation contains an extra Instruction Byte more
than the Read operation. Such Instruction Byte in Write
mode follows the Slave Address Byte. The MSB of the
Instruction Byte labeled
A
/B is the RDAC sub-address
select. A “low” select RDAC1 and a “high” selects RDAC2
for dual channel AD5282. The 2
nd
MSB RS is the Mid-
scale reset. A logic high of this bit moves the wiper of a
selected RDAC to the center tap where R
WA
=R
WB
. The 3
rd
MSB SD is a shutdown bit. A logic high causes the RDAC
open circuit at terminal A while shorting wiper to terminal
B. This operation yields almost a zero Ohm in rheostat
mode or zero volt in potentiometer mode. This SD bit
serves the same function as the
SHDN
pin except it reacts in
active low. The following two bits are O2 and O1. They are
extra programmable logic output that users can make use of
them by driving other digital loads, logic gates, LED
drivers, and analog switches, etc. The 3 LSBs are DON’T
CARE. See Figure 2.
3.
After acknowledged the Instruction Byte, the last byte in
Write mode is the Data Byte. Data is transmitted over the
serial bus in sequences of nine clock pulses (eight data bits
followed by an “Acknowledge” bit). The transitions on the
SDA line must occur during the low period of SCL and
remain stable during the high period of SCL, Figure 1.
4.
In Read mode, the Data Byte goes right after the
acknowledgment of the Slave Address Byte. Data is
transmitted over the serial bus in sequences of nine clock
pulses (slight difference with the Write mode, there are
eight data bits followed by a “No Acknowledge” bit).
Similarly, the transitions on the SDA line must occur
during the low period of SCL and remain stable during the
high period of SCL.
5.
When all data bits have been read or written, a STOP
condition is established by the master. A STOP condition is
defined as a low-to-high transition on the SDA line while
SCL is high. In Write mode, the master will pull the SDA
line high during the 10
th
clock pulse to establish a STOP
相关PDF资料 |
PDF描述 |
|---|---|
| AD5282 | Low Power, 8 Channel, 10-bit, 65MSPS ADC, 1.8V 257-BGA MICROSTAR 0 to 70 |
| AD5282BRU20 | 32-Tap. Nonvolatile. Linear-Taper Digital Potentiometers in SOT23 |
| AD5282BRU200 | 10-Bit, 40MSPS ADC Dual Ch., Low Power 48-TQFP -40 to 85 |
| AD5300BRM-REEL | +2.7 V to +5.5 V, 140 uA, Rail-to-Rail Output 8-Bit DAC in an SOT-23 |
| AD5300BRM-REEL7 | +2.7 V to +5.5 V, 140 uA, Rail-to-Rail Output 8-Bit DAC in an SOT-23 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5280BRU200-REEL7 | 制造商:Analog Devices 功能描述:Digital Potentiometer 256POS 200KOhm Single 14-Pin TSSOP T/R 制造商:Analog Devices 功能描述:DGTL POTENTIOMETER 256POS 200KOHM SGL 14TSSOP - Tape and Reel |
| AD5280BRU20-REEL7 | 制造商:Analog Devices 功能描述:Digital Potentiometer 256POS 20KOhm Single 14-Pin TSSOP T/R |
| AD5280BRU50 | 制造商:Analog Devices 功能描述:Digital Potentiometer 256POS 50KOhm Single 14-Pin TSSOP |
| AD5280BRU50-REEL7 | 制造商:Analog Devices 功能描述:Digital Potentiometer 256POS 50KOhm Single 14-Pin TSSOP T/R |
| AD5280BRUZ20 | 功能描述:IC DGTL POT 15V 20K 14-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
发布紧急采购，3分钟左右您将得到回复。