参数资料
| 型号： | AD5412AREZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 22/44页 |
| 文件大小： | 0K |
| 描述： | IC DAC 12BIT SER 24TSSOP |
| 设计资源： | Simplified 12-Bit Voltage and 4 mA-to-20 mA Output Solution Using AD5412 (CN0097) |
| 标准包装： | 62 |
| 设置时间： | 25µs |
| 位数： | 12 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字，双 ± |
| 功率耗散（最大）： | 128mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 24-TSSOP 裸露焊盘 |
| 包装： | 管件 |
| 输出数目和类型： | 1 电流，单极；1 电流，双极；1 电压，单极；1 电压，双极 |
| 采样率（每秒）： | 40k |
| 产品目录页面： | 782 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Data Sheet
AD5412/AD5422
Rev. I | Page 29 of 44
Readback Operation
Readback mode is invoked by setting the address byte and
read address when writing to the input register (see Table 9 and
NOP command, which clocks out the data from the previously
addressed register as shown in Figure 3.
By default the SDO pin is disabled after having addressed the
enables the SDO pin in anticipation of data being clocked out.
After the data has been clocked out on SDO, a rising edge on
LATCH disables (tristate) the SDO pin. To read back the data
register, for example, implement the following sequence:
1. Write 0x020001 to the input register. This configures the
part for read mode with the data register selected.
2. Follow this with a second write: a NOP condition, which is
0x000000. During this write, the data from the register is
clocked out on the SDO line.
Table 9. Read Address Decoding
Read Address
Function
00
Read status register
01
Read data register
10
Read control register
POWER-ON STATE
circuit ensures that all registers are loaded with zero-code. As
such, both outputs are disabled; that is, the VOUT and IOUT pins
are in tristate. The +VSENSE pin is internally connected to ground
through a 40 kΩ resistor. Therefore, if the VOUT and +VSENSE pins
are connected together, VOUT is effectively clamped to ground
through a 40 kΩ resistor. Also upon power-on, internal
calibration registers are read, and the data is applied to internal
calibration circuitry. For a reliable read operation, there must be
sufficient voltage on the AVDD supply when the read event is
triggered by the DVCC power supply powering up. Powering up
the DVCC supply after the AVDD supply ensures this. If DVCC and
AVDD are powered up simultaneously or the internal DVCC is
enabled, the supplies should be powered up at a rate greater
than, typically, 500 V/sec or 24 V/50 ms. If this cannot be
achieved, issue a reset command to the AD5412/AD5422 after
power-on; this performs a power-on-reset event, reading the
calibration registers and ensures specified operation of the
internal reference to settle to its correct trim value, 40 s should
be allowed after a successful power on reset.
Voltage Output
For a unipolar voltage output range, the output voltage can be
expressed as
×
=
N
REFIN
OUT
D
Gain
V
2
For a bipolar voltage output range, the output voltage can be
expressed as
2
REFIN
N
REFIN
OUT
V
Gain
D
Gain
V
×
×
=
where:
D is the decimal equivalent of the code loaded to the DAC.
N is the bit resolution of the DAC.
VREFIN is the reference voltage applied at the REFIN pin.
Gain is an internal gain whose value depends on the output
range selected by the user as shown in Table 10.
Table 10. Internal Gain Value
Output Range
Gain Value
+5 V
1
+10 V
2
±5 V
2
±10 V
4
Current Output
For the 0 mA to 20 mA, 0 mA to 24 mA, and 4 mA to 20 mA
current output ranges, the output current is respectively
expressed as
D
I
N
OUT
×
=
2
mA
20
D
I
N
OUT
×
=
2
mA
24
mA
4
2
mA
16
+
×
=
D
I
N
OUT
where:
D is the decimal equivalent of the code loaded to the DAC.
N is the bit resolution of the DAC.
Table 11. Input Shift Register Contents for a Read Operation
MSB
LSB
D23
D22
D21
D20
D19
D18
D17
D16
D15 to D2
D1
D0
0
1
0
Read address
1
X = don’t care.
相关PDF资料 |
PDF描述 |
|---|---|
| ADA4938-2ACPZ-R7 | IC ADC DRIVER DIFF DUAL 24LFCSP |
| DAC8043A1ESZ | IC DAC 12BIT MULT SRL INP 8SOIC |
| VI-2WN-IV-F2 | CONVERTER MOD DC/DC 18.5V 150W |
| VI-B3X-MX-S | CONVERTER MOD DC/DC 5.2V 75W |
| VI-2WN-IV-F1 | CONVERTER MOD DC/DC 18.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5412AREZ | 制造商:Analog Devices 功能描述:IC DAC 12BIT TSSOP-24 制造商:Analog Devices 功能描述:IC, DAC, 12BIT, TSSOP-24 |
| AD5412AREZ-REEL7 | 功能描述:IC DAC 12BIT SER 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5412BCPZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Single Channel, 12/16-Bit, Serial Input, Current Source & Voltage Output DAC |
| AD5412BREZ | 制造商:Analog Devices 功能描述: |
| AD5415 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual 12-Bit, High Bandwidth, Multiplying DAC with 4-Quadrant Resistors and Serial Interface |
发布紧急采购，3分钟左右您将得到回复。