参数资料
| 型号： | AD5433YCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/29页 |
| 文件大小： | 0K |
| 描述： | IC DAC 10BIT MULTIPLYING 20LFCSP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 1 |
| 设置时间： | 35ns |
| 位数： | 10 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 25µW |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-VQ |
| 包装： | 托盘 |
| 输出数目和类型： | 2 电流，单极；2 电流，双极 |
| 采样率（每秒）： | 20.4M |
| 配用： | EVAL-AD5433EBZ-ND - BOARD EVAL FOR AD5433 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD5424/AD5433/AD5445
Data Sheet
Rev. D | Page 22 of 28
Table 9. Suitable ADI Precision References
Part No.
Output Voltage (V)
Initial Tolerance (%)
Temp Drift (ppm/°C)
ISS (mA)
Output Noise (V p-p)
Package
10
0.05
3
1
20
SOIC-8
10
0.05
9
1
20
TSOT-23, SC70
5
0.06
3
1
10
SOIC-8
5
0.06
9
1
10
TSOT-23, SC70
2.5
0.10
3
1
6
SOIC-8
2.5
0.10
9
1
6
TSOT-23, SC70
3
0.10
3
1
10
SOIC-8
3
0.10
9
1
10
TSOT-23, SC70
2.5
0.04
3
0.8
3.5
SOIC-8
5
0.04
3
0.8
8
SOIC-8
2.5
0.16
9
0.12
5
TSOT-23
5
0.10
9
0.12
8
TSOT-23
Table 10. Suitable ADI Precision Op Amps
Part No.
Supply Voltage (V)
VOS (Max) (V)
IB (Max) (nA)
0.1 Hz to 10 Hz
Noise (V p-p)
Supply Current (A)
Package
±2 to ±20
25
0.1
0.5
600
SOIC-8
±2.5 to ±15
60
2
0.4
500
MSOP, SOIC-8
2.7 to 5
5
0.05
1
975
MSOP, SOIC-8
1.8 to 6
50
0.001
2.3
50
TSOT
2.7 to 6
5
0.1
0.5
850
TSOT, SOIC-8
Table 11. Suitable ADI High Speed Op Amps
Part No.
Supply Voltage (V)
BW at ACL (MHz)
Slew Rate (V/s)
VOS (Max) (V)
IB (Max) (nA)
Package
5 to 24
145
180
1500
6000
SOIC-8, SOT-23, MSOP
±2.5 to ±12
490
120
1000
10500
SOIC-8, MSOP
3 to 12
350
425
3000
750
SOIC-8, SC70-5
±3 to ±6
320
1300
10000
7000
SOIC-8
REFERENCE SELECTION
AD5445 family of current output DACs, pay attention to the
reference’s output voltage temperature coefficient specification.
This parameter not only affects the full-scale error, but can also
affect the linearity (INL and DNL) performance. The reference
temperature coefficient should be consistent with the system
accuracy specifications. For example, an 8-bit system required
to hold its overall specification to within 1 LSB over the
temperature range 0°C to 50°C dictates that the maximum
system drift with temperature should be less than 78 ppm/°C.
A 12-bit system with the same temperature range to overall
specification within 2 LSBs requires a maximum drift of
10 ppm/°C. By choosing a precision reference with low output
temperature coefficient this error source can be minimized.
Table 9 suggests some references available from Analog Devices
that are suitable for use with this range of current output DACs.
AMPLIFIER SELECTION
The primary requirement for the current-steering mode is an
amplifier with low input bias currents and low input offset
voltage. The input offset voltage of an op amp is multiplied by
the variable gain (due to the code dependent output resistance
of the DAC) of the circuit. A change in the noise gain between
two adjacent digital fractions produces a step change in the output
voltage due to the amplifier’s input offset voltage. This output
voltage change is superimposed on the desired change in output
between the two codes and gives rise to a differential linearity
error, which, if large enough, could cause the DAC to be non-
monotonic. In general, the input offset voltage should be <1/4
LSB to ensure monotonic behavior when stepping through codes.
The input bias current of an op amp also generates an offset at
the voltage output as a result of the bias current flowing into the
feedback resistor, RFB. Most op amps have input bias currents
low enough to prevent significant errors in 12-bit applications.
Common-mode rejection of the op amp is important in voltage-
switching circuits, since it produces a code dependent error at
the voltage output of the circuit. Most op amps have adequate
common mode rejection for use at 8-, 10-, and 12-bit resolution.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JNM-MZ-F2 | CONVERTER MOD DC/DC 10V 25W |
| MS3120F22-21P | CONN RCPT 21POS WALL MNT W/PINS |
| VI-B1L-MV-F3 | CONVERTER MOD DC/DC 28V 150W |
| MS27473T24F24S | CONN PLUG 24POS STRAIGHT W/SCKT |
| VI-B1L-MV-F2 | CONVERTER MOD DC/DC 28V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5433YRU | 功能描述:IC DAC 10BIT MULTIPLYING 20TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5433YRU-REEL | 功能描述:IC DAC 10BIT MULTIPLYING 20TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5433YRU-REEL7 | 制造商:Analog Devices 功能描述:DAC 1-CH R-2R 10-bit 20-Pin TSSOP T/R 制造商:Analog Devices 功能描述:DAC 1CH R-2R 10-BIT 20TSSOP - Tape and Reel |
| AD5433YRUZ | 功能描述:IC DAC 10BIT MULTIPLYING 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:1 系列:- 设置时间:4.5µs 位数:12 数据接口:串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOICN 包装:剪切带 (CT) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:* 其它名称:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD5433YRUZ | 制造商:Analog Devices 功能描述:10BIT DAC PARALLEL I/F SMD 5433 |
发布紧急采购，3分钟左右您将得到回复。