- 您现在的位置：买卖IC网 > PDF目录3494 > AD5750ACPZ-REEL7 (Analog Devices Inc)IC CURR/VOLT OUT DVR 32LFCSP PDF资料下载
参数资料
| 型号： | AD5750ACPZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 21/36页 |
| 文件大小： | 0K |
| 描述： | IC CURR/VOLT OUT DVR 32LFCSP |
| 标准包装： | 1,500 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 转换速率： | 2 V/µs |
| 电流 - 电源： | 5.2mA |
| 电流 - 输出 / 通道： | 24mA |
| 电压 - 电源，单路/双路(±)： | ±10.8 V ~ 26.4 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
AD5750/AD5750-1
Rev. C | Page 28 of 36
Readback Operation
Readback mode is activated by selecting the correct device address
(A2, A1, A0) and then setting the R/W bit to 1. By default, the
SDO pin is disabled. After having addressed the AD5750/
AD5750-1 for a read operation, setting R/W to 1 enables the
SDO pin and SDO data is clocked out on the 5th rising edge of
SCLK. After the data has been clocked out on SDO, a rising
edge on SYNC disables (tristate) the SDO pin again. Status
register data (see
) and control register data are both
available during the same read cycle.
The status bits comprise four read-only bits. They are used to
notify the user of specific fault conditions that occur, such as
an open circuit or short circuit on the output, overtemperature
error, or an interface error. If any of these fault conditions occur,
a hardware FAULT is also asserted low, which can be used as a
hardware interrupt to the controller.
See the Detailed Description of Features section for a full
explanation of fault conditions.
HARDWARE CONTROL
Hardware control is enabled by connecting the HW SELECT
pin to DVCC. In this mode, the R3, R2, R1, and R0 pins in
conjunction with the RSET pin are used to configure the output
range, as per Table 8.
In hardware mode, there is no status register. The fault condi-
tions (open circuit, short circuit, and overtemperature) are
available on Pin IFAULT, Pin VFAULT, and Pin TEMP. If any
one of these fault conditions are set, then a low is asserted on
the specific fault pin. IFAULT, VFAULT, and TEMP are open-
drain outputs and therefore can be connected together to allow
the user to generate one interrupt to the system controller to
communicate a fault. If hardwired in this way, it is not possible
to isolate which fault occurred in the system.
TRANSFER FUNCTION
The AD5750/AD5750-1 consist of an internal signal
conditioning block that maps the analog input voltage to a
programmed output range. The available analog input ranges
are 0 V to 4.096 V (AD5750) and 0 V to 2.5 V (AD5750-1).
For all ranges, both current and voltage, the AD5750 and
AD5750-1 implement a straight linear mapping function, where
0 V maps to the lower end of the selected range and 4.096 V (or
2.5 V for AD5750-1) maps to the upper end of the selected range.
Table 9. Input Shift Register Contents for a Read Operation—Status Register
MSB
LSB
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
A2
A1
A0
1
0
R3
R2
R1
R0
CLRSEL
OUTEN
RSET
PEC error
OVER TEMP
IOUT fault
VOUT fault
Table 10. Status Bit Options
Bit
Description
PEC Error
This bit is set if there is an interface error detected by CRC-8 error checking. See the Detailed Description of Features section.
OVER TEMP
This bit is set if the AD5750/AD5750-1 core temperature exceeds approximately 150°C.
IOUT Fault
This bit is set if there is an open circuit on the IOUT pin.
VOUT Fault
This bit is set if there is a short circuit on the VOUT pin.
相关PDF资料 |
PDF描述 |
|---|---|
| 9-146253-0-29 | CONN HDR BRKWAY .100 58POS VERT |
| CLT-109-01-L-D | CONN RCPT 18POS DUAL 2MM T/H |
| CLT-118-01-L-D | CONN RCPT 36POS DUAL 2MM T/H |
| 9-146305-0-26 | CONN HEADR BRKWAY .100 26POS R/A |
| 41276 | CONN IDENTIFICATION BAND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5750BCPZ | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| AD5750BCPZ-REEL | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| AD5750BCPZ-REEL7 | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| AD5751 | 制造商:AD 制造商全称:Analog Devices 功能描述:Industrial Current/Voltage Output Driver |
| AD5751ACPZ | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。